Reproduction GM bumper bolt for a variety of General Motors and Chrysler applications. Each zinc-plated steel carriage bolt features a polished stainless steel cap for superb cosmetic appearance, corrosion resistance and long...
Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
Bolt, 5/16-18 x 13/16" Pointed Tip With Hex Washer Head, Black Phosphate
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1962-76 GM, Dodge, Plymouth; Various Models; Convertible Top Boot Vinyl Storage Bag
Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot vinyl storage bag. The storage bag will help protect your vehicles top boot while being stored in...
1966-74 Dodge/Plymouth A & B-Body; Exterior Door Mirror; Round Head; With Remote; LH Driver Side
Freshen the look of your Dodge or Plymouth by replacing your pitted, damaged or missing mirror with this brand new replacement remote outer door mirror for 1966-74 A-body models with a vent window or 1966-70 B-body models...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
1967-74 Dodge, Plymouth; A, B-Body; Outer Door Mirror; Single Post; with Hardware; RH or LH; Each
Reproduction of the original outer single post door mirror for 1967-74 Dodge and Plymouth A-Body or 1968-70 Dodge and Plymouth B-Body models. Each outer door mirror is manufactured in die-cast zinc featuring a bright chrome...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
Windshield Wiper Blades; Aero Style; 15"; for 1/4" (7mm) Bayonet Style Arms; Pair; Various Models
High quality reproduction of the stainless steel "Aero" Anti Wind-Lift Wiper Blades designed to fit 7mm wide bayonet style wiper arms. Popularized in the 1960's and 70's to combat wind lift at high speeds, these 15 inch wiper...
Reproduction outer door handles for various 1967-70 Dodge and Plymouth models as listed below. Each door handle is manufactured in quality die-cast zinc featuring a polished chrome finish replicating the original in design,...
1966-70 Chrysler, Plymouth, Dodge A, B, C-Body; Convertible Top Hydraulic Cylinder; Each
Reproduction of the original convertible top cylinder designed for use with 1966-70 Chrysler, Dodge and Plymouth A, B, and C Body convertible models as listed. All convertible top cylinders are not the same. This convertible...
1966-74 Dodge, Plymouth; Lower Front Door Hinge; LH; Driver Side; Various Models
Reproduction door hinge for various Dodge and Plymouth A and B-Body models. The front doors on 1966-74 Mopar A and B-Body models were extremely heavy and hard on the original door hinges. Each door hinge is reproduced to...
16" Windshield Wiper Blade Refill; Pair; 16" x 3/8" wide
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
1967-74 Dodge, Plymouth A-Body; Upper Front Door Hinge; RH; Passenger Side
Reproduction of the original door hinge for various Dodge and Plymouth A-Body models. The front doors on 1967-74 Mopar A-Body models were extremely heavy and hard on the original door hinges. Each door hinge is reproduced to...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
1963-70 Dodge, Plymouth; Windshield Washer F Connector; A-Body Models; White
Reproduction of the original windshield washer "F" style connector designed for use with 1963-70 Mopar A body models. Built to original specifications and features the correct coloration for an unmatched fit and appearance....
1960-84 Windshield Wiper Blade; 16" Trico; Rainbow Type; 1/4" Bayonet Connector; Matt Stainless
Reproduction of the original Trico Rainbow Type wiper blade designed for various models originally equipped with Trico blades. Each wiper blade will replace the original and offer years of service. Each blade comes complete...