1967-68 Mustang; Rear Bumper; Chrome; OER Premier; Show Quality
Premier quality reproduction rear bumper for 1967-68 Ford Mustang models. Manufactured to exact factory specifications, each bumper features a triple plated chrome finish that replicates the original in quality, appearance...
1967-68 Mustang; Front Bumper; Chrome; OER Premier; Show Quality
Premier quality reproduction front bumper for 1967-68 Ford Mustang models. Manufactured to exact factory specifications, each bumper features a triple plated chrome finish that replicates the original in quality, appearance...
Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1967-68 Mustang, Cougar; Fender Apron and Shock Tower Assembly; Drivers Side; EDP Coated
1967-68 Mustang and Cougar full shock tower assembly with 1-piece inner fender apron, shock tower and frame rail welded together. Fender aprons feature correct holes to accept the fender nuts and is a one-piece style to...
1967-68 Mustang Fastback; Rear Window Glass; Flush Mount; Glue-In; No Molding Needed; Clear
Flush mount back window glass for 1967-68 Ford Mustang fastback models. This custom made back window glass is manufactured slightly larger than the original allowing you to eliminate the outer stainless trim. Direct fit...
Flush mount back window glass for 1967-68 Ford Mustang fastback models. This custom made back window glass is manufactured slightly larger than the original allowing you to eliminate the outer stainless trim. Direct fit...
1964-68 Ford Mustang; Front Windshield Glass; Flush Mount; No Molding Needed; Clear
Flush mount front windshield glass for 1964-68 Ford Mustang models. This custom made windshield glass is manufactured slightly larger than the original allowing you to eliminate the outer stainless trim. Designed to glue in...
1962-76 GM, Dodge, Plymouth; Various Models; Convertible Top Boot Vinyl Storage Bag
Why leave your top boot in the trunk exposed when you can keep it safe and clean by safely storing it in this special top boot vinyl storage bag. The storage bag will help protect your vehicles top boot while being stored in...
1967-68 Mustang Fastback; Door Glass Assembly; Clear Glass; Passenger Side
Correct reproduction of the original door glass assembly designed for 1967-68 Mustang fastback models. Includes the correct run channel to completely replace the entire glass unit. The glass carrier is manufactured from...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
1967-68 Mustang, Cougar; Door Glass Assembly; Coupe; Clear Glass; Passenger Side
Correct reproduction of the original door glass assembly designed for 1967-68 Mustang/Cougar coupe. Includes the correct lower channel to completely replace the entire glass unit. The glass carrier is manufactured from...
1967-68 Mustang; Door Glass Assembly; Convertible; Tinted Glass; Passenger Side
Correct reproduction of the original door glass assembly designed for 1967-68 Mustang convertible models. Includes the correct run channel to completely replace the entire glass unit. The glass carrier is manufactured from...
1967-68 Mustang; Fastback; Back Glass; Smoke Gray Tint
OER Authorized reproduction back window glass for 1967-68 Mustang Fastback. Replacing scratched, damaged, or missing rear window glass will enhance your vehicle's value by improving the cosmetic appearance, while also...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
1967-68 Mustang Fastback; Rear Window Glass; Light Green Tint
OER reproduction of the original back window glass designed for use with 1967-68 Mustang Fastback models. Each rear window glass is manufactured to factory specifications featuring correct glass shape and contours for proper...
High-quality reproduction of the stainless steel "Aero" Anti-Wind-Lift wiper blades designed to fit 7mm wide bayonet-style wiper arms. Popularized in the 1960s and 1970s to combat wind lift at high speeds, these 15" wiper...
1967-68 Mustang Convertible Door Window Frame Set - RH
Reproduction door window frame assembly for 1967-68 Mustang convertible. Features a polished outer frame, with a sturdy lower frame to attach to your window regulators. For your convenience, these are sold individually, so...