1947-91 GM; Rubber Bumper / Stopper; Various Applications
OER® reproduction of the original style rubber bumper designed for use with various GM applications. Each rubber stopper is manufactured to correct specifications in EPDM rubber ensuring long lasting quality. Will fit...
OER butyl rubber sealant for installing front windshield or back glass installation. Can be used on virtually all models of Chrysler, GM, and Ford that did not use a contoured molded style weatherstrip for installation of the...
1965-72 GM; Wiring Harness Firewall Retainer Gutter; 13" Long; OER
Reproduction firewall wiring harness gutter for a wide variety of vehicles. This reproduction wire harness gutter holds the engine harness as it passes against the firewall area to protect the wiring harness as it crosses...
1961-64 Impala & 1964-72 El Camino Gas Door Bumpers 1937-58 1-prong Door Bumpers- Pair
Correct reproduction rubber bumper for various GM applications. Fits: 1937-1958 GM full size door bumper, single prong style, front or rear. 1961-64 full size and 1964-72 El Camino gas filler door. Keeps the door from...
1955-59 Truck, 1955 Car 4-Hole 1-5/8" OD Wire Harness Grommet (Large)
Reproduction of the large 4-hole firewall wire harness grommet for all 1955 Chevrolet cars and 1955-59 Chevrolet and GMC trucks. Can also be used for custom or as a universal fit grommet for other applications. Measures 1...
Rubber Floor Pan Plug; 1-1/4" Diameter. Fits 1" Hole; Each
Reproduction rubber floor pan plug measures 1-1/4" diameter and fits a 1" hole. Sold individually, use as required.
1964-72 Buick, Chevrolet, Oldsmobile, Pontiac; Fuel Tank Vent Tube Grommet; Each
Replacement vent tube grommet for 1964-72 GM models. Manufactured to factory dimensions, this molded rubber grommet fits in the trunk pan and features two holes for the fuel vent tube to pass through. {fitment}
1959-79 Buick, Chevy, Pontiac, Oldsmobile; Seat Back Bumper; Oval Style; Each; Various Models
Reproduction of the original oval style seat back bumper designed for use on various 1959-79 GM vehicles. Each bumper is manufactured in hard rubber including a steel core for added strength. The bumper is installed where the...
Nylon Fastener; 13/64" Dia. Stem; 13/32" Stem Length; For Door/Header Weatherstrip; Natural
This reproduction door weatherstrip clip is used on most GM vehicles which require plastic push in clips. These hook into holes in the door rubber weatherstripping and hold the weatherstrip to the door. Also used on Most GM...
1955-81 Chevrolet, GMC, Pontiac; Air Cleaner Lid Rubber Seal; 59" Long x 5/16" Wide
Reproduction air cleaner lid seal for a variety of GM car and truck models as listed. Designed to seal the area between the lid and the base offering a tight seal for the air cleaner on models that required this seal. {specs}...
Staple For Inner Fender Splash Apron, 1/2 inch
Correct staple to install fender skirt splash aprons for various models. 1/2" wide, 1/2" deep.
1942-77 GM; Hood Adjustment Rubber Bumpers; Round; Pair; Various Models
Reproduction hood adjustment bumpers for various 1942-77 GM models. These 7/8" OD reproduction stoppers are manufactured in quality rubber and designed to replace the worn out, deteriorated, or lost originals. Allows for a...
Reproduction weatherstrip clip receiver seal for 1958-71 GM models. These small plugs are inserted into the door and provide a mounting point for the door frame weatherstrip clips to insert into. Sold individually. 26...
1966-72 GM; Outer Mirror Mounting Set ; LH or RH ; Gasket, Bracket, Screws
Reproduction of the original style components required to replace and mount the outer door mirror on the door. Contains all the necessary hardware to install a standard outer door mirror onto either the drivers or passenger...
1955-1976 GM; Rubber Floor Pan Plug; Fits 1-1/2" Hole; Each
Reproduction of the original round rubber floor pan plug installed on various 1955-76 General Motors vehicles. Found in various locations on the floor pan, these plugs are manufactured to factory specifications in quality...
Sealstrip Glass Setting Tape; 10 Foot Roll; 1/32" Tape Thickness
Replacement glass setting tape for various models. This glass tape holds glass firmly and permanently. Seals against dirt, moisture, and will not stretch out of shape. Just fold it over the glass edge, insert glass in the...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1968-72 Lower Control Arm Bumper ; Each
Reproduction of the original lower control arm bumper designed for use on various GM vehicles including 1968-69 Camaro and Firebird models. Each control arm bumper is manufactured in hard rubber featuring correct mounting...
1962-81 GM; Glove Box Door Arm Rubber Bumper
OER® reproduction of the original glove box door arm rubber bumper designed for use with various 1962-81 GM models. This rubber bumper is manufactured in EPDM rubber to the original factory configuration. Was installed on...
1951-75 Convertible Power Top Motor Mounting Grommet - Each
Reproduction of the original rubber mounting / insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a...