1967 Camaro SS, 1968-72 Nova SS; Hood Louvers; with Hardware; RH & LH; Pair; "Show Quality"
Reproduction hood louvers for 1967 Camaro SS and 1968-72 Nova SS models. Each hood louver is manufactured in quality die-cast zinc replicating the original design, appearance, and fitment. Features correct black paint scheme,...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1965-69 Impala, Camaro, Nova, Firebird; Hood Hinge; LH; Driver Side
Reproduction of the original hood hinge assembly designed for various GM models. Each hood hinge is manufactured from stamped steel assuring a quality replacement. We recommend replacing the hood spring when installing a new...
1970-81 Camaro, Firebird, 67, 69 Impala, Caprice, Hood Hinge Spring; Each; Various Models
Reproduction of the original hood hinge spring designed for use on various GM vehicles. Each spring is manufactured to replicate the original in quality and design. Will fit and install as original and features OE tension...
1967-69 Camaro, Firebird, 1966-79 Nova; Fiberglass Hood Springs; 11 lbs; Low Tension Design; Pair
Never have to use a 'prop' rod on your fiberglass hood again. These lower tension springs allow you to retain the original hood functionality without needing assistance to open it. Designed to fit in the stock position, these...
Newly tooled heavy duty heat treated OER Premier reproduction hood hinge assembly set for 1967-72 Chevrolet and GMC truck models. Each hood hinge set has been re-tooled to be a perfect replication of the factory original that...
1967 Chevelle, Malibu, El Camino; Hood Latch Assembly
Reproduction hood latch assembly for 1967 Chevrolet Chevelle, Malibu, El Camino models. Each hood latch assembly is manufactured in stamped steel to original factory specifications featuring correct contours for an authentic...
1967-70 Camaro, 1965-68 Impala, Bel Air, Caprice, 1968 Chevelle; Hood Latch Pop-Up Spring
Reproduction hood pop-up spring for 1967-81 Camaro, 1965-68 Impala, Bel Air, Biscayne, Caprice, and 1968 Chevelle, El Camino models. Measures 3-3/4" long and features a black EDP coating for rust and corrosion prevention....
1967-69 Chevy Camaro; Cowl Induction Hood Spring; 26 Coils; Each; Made in the USA!
Reproduction of the original 1969 Camaro cowl induction hood spring. Can also be used for 1967-68 Camaro models with cowl hoods. Manufactured to exact dimensions from premium grade spring steel with a black chromate finish...
1967-68 Camaro; Hood Lock Catch Support; All Models; EDP Coated
Reproduction hood lock catch support for 1967-68 Camaro models. The hood latch catch support is located between the grill and radiator support. This support also helps strengthen the entire front section of the vehicle. This...
1967 Camaro; Hood Release Assembly; Standard Hood
Reproduction of the original hood latch assembly for use with 1967 Camaro models. Each hood release is manufactured to factory specifications featuring the correct latch and spring mechanism. Will bolt directly to any...
1967-92 Camaro, Firebird; Hood Prop Rod for Fiberglass Hoods; Each; Made in the USA!
Hood prop required when installing a fiberglass hood on your Camaro or Firebird. Since hood springs are not recommended when using fiberglass hoods, this prop is essential for keeping your hood open while working in the...
1967 Impala, 1968-69 Camaro; SS Hood Louver Drains; Pair; Made in the USA!
Reproduction of the original Super Sport hood louver drain tubes for use with 1967 Impala SS, and 1968-69 Camaro Super Sport models. These drain tubes install under the hood substructure and are designed to direct water from...
1967-81 GM; Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; for Hood Hinges; 8 Piece Set; Various Models
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
Reproduction hood lock catch support or striker plate for 1967-80 Chevrolet and GMC trucks and SUV models (without inner cable-operated hood release). Each support is produced in stamped steel with the threaded nut welded in...
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...
1970-2002 GM; Hood Insulation Fastener; Each
Replacement black nylon hood insulation fastener is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models. It...
Reproduction hood hinge spring for various GM models including Chevelle, Camaro, Impala, Firebird and other various GM models. Each spring is designed and manufactured to exact factory specifications for the models listed...
1965-69 Impala, Camaro, Nova, Firebird; Hood Hinge; RH; Passenger Side
Reproduction of the original hood hinge assembly designed for various GM models. Each hood hinge is manufactured from stamped steel assuring a quality replacement. We recommend replacing the hood spring when installing a new...