OER butyl rubber sealant for installing front windshield or back glass installation. Can be used on virtually all models of Chrysler, GM, and Ford that did not use a contoured molded style weatherstrip for installation of the...
1965-72 GM; Wiring Harness Firewall Retainer Gutter; 13" Long; OER
Reproduction firewall wiring harness gutter for a wide variety of vehicles. This reproduction wire harness gutter holds the engine harness as it passes against the firewall area to protect the wiring harness as it crosses...
1965-66 Impala, Bel Air, Caprice; Door Frame Weatherstrip, 2 Door Sedan, Pair
Reproduction of the original door frame weatherstripping designed for use on 1965-66 Impala/Full Size Chevrolet and Pontiac Catalina 2-Door Sedan models. Each weatherstrip is designed to replace the original and offer a tight...
1955-59 Truck, 1955 Car 4-Hole 1-5/8" OD Wire Harness Grommet (Large)
Reproduction of the large 4-hole firewall wire harness grommet for all 1955 Chevrolet cars and 1955-59 Chevrolet and GMC trucks. Can also be used for custom or as a universal fit grommet for other applications. Measures 1...
Rubber Floor Pan Plug; 1-1/4" Diameter. Fits 1" Hole; Each
Reproduction rubber floor pan plug measures 1-1/4" diameter and fits a 1" hole. Sold individually, use as required.
1957-70 Buick, Cadillac, Chevy, Pontiac, Oldmobile; Trunk Weatherstrip; Various Full Size Models
Reproduction of the original trunk weatherstrip manufactured in the correct configuration. Prevent water damage in your trunk area by replacing the worn and damaged weatherstrip with this authentic reproduction. The soft...
1959-79 Buick, Chevy, Pontiac, Oldsmobile; Seat Back Bumper; Oval Style; Each; Various Models
Reproduction of the original oval style seat back bumper designed for use on various 1959-79 GM vehicles. Each bumper is manufactured in hard rubber including a steel core for added strength. The bumper is installed where the...
Nylon Fastener; 13/64" Dia. Stem; 13/32" Stem Length; For Door/Header Weatherstrip; Natural
This reproduction door weatherstrip clip is used on most GM vehicles which require plastic push in clips. These hook into holes in the door rubber weatherstripping and hold the weatherstrip to the door. Also used on Most GM...
1955-81 Chevrolet, GMC, Pontiac; Air Cleaner Lid Rubber Seal; 59" Long x 5/16" Wide
Reproduction air cleaner lid seal for a variety of GM car and truck models as listed. Designed to seal the area between the lid and the base offering a tight seal for the air cleaner on models that required this seal. {specs}...
Staple For Inner Fender Splash Apron, 1/2 inch
Correct staple to install fender skirt splash aprons for various models. 1/2" wide, 1/2" deep.
1942-77 GM; Hood Adjustment Rubber Bumpers; Round; Pair; Various Models
Reproduction hood adjustment bumpers for various 1942-77 GM models. These 7/8" OD reproduction stoppers are manufactured in quality rubber and designed to replace the worn out, deteriorated, or lost originals. Allows for a...
1955-90 GM; Door Lock Gasket; Various Models
Reproduction of the original door lock gasket designed for use on various GM models including the listings below. After repainting your doors, or whenever replacing door locks, be sure to install new lock cylinder gaskets to...
1958-77 Buick, Chevy, Olds, Pontiac; Hood Adjust Bumper and Screw Set ; Various Models
Reproduction hood adjustment bumpers for various 1958-77 GM models including 1967-69 Camaro and Firebird models. These 7/8" OD reproduction stoppers and screws are manufactured to original specifications to replace the worn...
1955-1976 GM; Rubber Floor Pan Plug; Fits 1-1/2" Hole; Each
Reproduction of the original round rubber floor pan plug installed on various 1955-76 General Motors vehicles. Found in various locations on the floor pan, these plugs are manufactured to factory specifications in quality...
1955-1981 GM; Firewall Pad Fastener; Each
This reproduction firewall pad fastener is designed to hold the firewall insulation pad in place on various 1955-81 General Motors models. Each fastener is manufactured from EPDM rubber replicating the original configuration...
1962-70 Chevrolet; Pontiac; Control Arm Bumper; Rubber; Various Models
Reproduction of the original control arm bumper designed for use on various GM models. Each bumper is manufactured to factory specifications in the correct configuration and includes a built in stud ensuring a perfect fit....
1962-81 Trunk Lock Cylinder Gasket ; Die-Cut Replacement
Reproduction die-cut trunk lock cylinder gasket designed to seal the trunk lock cylinder to the body. This gasket is designed for use on the listings below. Each gasket will fit and function as original. This is a non-molded...
1962-66 Door Rubber Bumper Set ; 4 Piece Set ; Various Models
Replacing the rubber door stoppers will help keep your doors aligned correctly while adding a factory fresh appearance to the vehicle. Each rubber bumper is designed and manufactured to exact OE specs. Manufactured in quality...
1951-75 Convertible Power Top Motor Mounting Grommet - Each
Reproduction of the original rubber mounting / insulation grommet used on various GM vehicles with the optional power top. These rubber grommets install on the pump assembly and secure it to the vehicle while creating a...
1958-75 Clutch Bellcrank Felt Seals ; Pair
OER® reproduction of the original die-cut felt seals that slips over the bellcrank pivot studs and seals against the end of the bellcrank tube to prevent dirt and water damage. Manufactured to correct dimensions. Sold in...