Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
1963-67 Chevrolet, Oldsmobile, Pontiac; Hood Hinge Assembly; RH Passenger Side
Reproduction hood hinge assembly for various 1963-67 GM models. Each hood hinge is manufactured from stamped steel to factory specifications assuring a quality replacement. Features correct mounting points for ease of...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
High-quality reproduction of the stainless steel "Aero" Anti-Wind-Lift wiper blades designed to fit 7mm wide bayonet-style wiper arms. Popularized in the 1960s and 1970s to combat wind lift at high speeds, these 15" wiper...
Correctly reproduced glass windshield washer bottle that was common in various 1955-72 General Motors vehicles. Each bottle is manufactured in the correct factory configuration that replaces the old or missing original...
1963-69 Buick, Chevrolet, GMC, Oldsmobile, Pontiac; Windshield Wiper Motor; 1 Speed; Brand New
Brand New Reproduction wiper motor built using the industry's most advanced engineering technology. Core shortages and low availability have made our brand new replacement wiper motors the high quality, low cost alternative...
1964-66 GM A/B Body; Front Door Latch; 2 Door; LH Driver Side; Various Models
Reproduction front door latch for various GM models. Replacing the latch can help the door to operate smoothly and correctly the way the factory intended. The finest manufacturing methods are employed offering a reproduction...
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
1964-67 GM A/B Body; Front Door Latch; 2 Door; RH Passenger Side; Various Models
Reproduction front door latch for various GM models. Replacing the latch can help the door to operate smoothly and correctly the way the factory intended. The finest manufacturing methods are employed offering a reproduction...
1959-76 GM; Convertible Top Boot Silde Rail Retainer; with 8 Mounitng Holes
Reproduction of the original style convertible top boot retainer for 1959-76 Buick, Chevrolet, Pontiac, and Oldsmobile convertible models (except Camaro, Firebird). The top boot will slide into this retainer in order to hold...
Reproduction of the original convertible top latch knuckle designed for use with a variety of 1964-72 Buick, Cadillac, Chevrolet, Pontiac, and Oldsmobile convertible models. Manufactured in quality zinc die-cast metal, each...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
Reproduction of the original convertible top latch knuckle designed for use with a variety of 1964-72 GM convertible models. Manufactured in quality zinc die-cast metal, each knuckle is built to OE factory specifications for...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
1967-81 GM; Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; for Hood Hinges; 8 Piece Set; Various Models
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....