Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1955-82 Spare Tire Hold Down Nut; 5/16"-18 Thread; 3.88" Wide; Zinc Finish
OER® reproduction wing nut for many GM models. This spare tire hold down nut is used in conjunction with the spare tire hold down rod. Manufactured in stamped steel and features correct threads and wing nut design....
1962-72 Chevrolet/Pontiac; OE Style Firewall Pad Fastener; Plastic; 7/16" X 1.50"; Various Models
Correct reproduction plastic firewall pad fastener for various GM models including 1967-69 Camaro, 1967-69 Firebird, 1962-72 Nova and 1962-69 Impala models. These fasteners are required to allow the firewall pad to attach...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1963-67 Chevrolet Corvette; Rear Bumper; Chrome; Driver Side; LH Driver Side
Reproduction of the original rear chrome bumper for 1963-67 Chevrolet Corvette models. Each bumper is designed and manufactured to factory specifications featuring correct mounting points and triple chrome plating. This...
1963-67 Chevrolet Corvette; Rear Bumper; Chrome; RH Passenger Side
Reproduction of the original rear chrome bumper for 1963-67 Chevrolet Corvette models. Each bumper is designed and manufactured to factory specifications featuring correct mounting points and triple chrome plating. This...
1963-67 Chevrolet Corvette; Chrome Front Bumper; RH Passenger Side
Reproduction of the original front bumper for use with 1963-67 Chevrolet Corvette models. Each bumper is manufactured to correct factory specifications offering an authentic appearance anf fitment. Features a triple chrome...
1963-67 Chevrolet Corvette; Chrome Front Bumper; LH Driver Side
Reproduction of the original front bumper for use with 1963-67 Chevrolet Corvette models. Each bumper is manufactured to correct factory specifications offering an authentic appearance anf fitment. Features a triple chrome...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
High-quality reproduction of the stainless steel "Aero" Anti-Wind-Lift wiper blades designed to fit 7mm wide bayonet-style wiper arms. Popularized in the 1960s and 1970s to combat wind lift at high speeds, these 15" wiper...
1964-72 Buick, Cadillac, Chevy, Pontiac, Oldsmobile; Convertible Top Latch Knuckle Hook; Each
Reproduction of the original latch knuckle hook designed for use with various GM convertible models. This component secures the convertible top to the upper windshield header, ensuring a proper seal and stable fit. Each...
Ford, GM, Mopar; Windshield Wiper Blade Refill; 16"; Pair
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
Reproduction of the original hose retainer clip designed for use with 1967-69 GM convertible models. Each clip is manufactured in stamped steel and heat treated for extra strength. This clip is designed to retain the...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
Reproduction zinc-plated bumper bolt with a polished stainless steel capped head for a variety of GM, Ford and Mercury applications including 1958-66 Chevrolet, 1965-68 Ford Mustang, 1960-67 Ford Falcon and 1960-65 Mercury...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...