Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1964-67 GM; Fuel Tank Sending Unit; 3/8"
The most accurate reproduction fuel tank sending unit in the industry, with original design for an authentic fit and genuine appearance. Each sending unit includes the sender, gasket, filter, and a brass float as original....
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
1959-66 Pontiac; Tri-Power Throttle Body; For 389/421 Engine
Reproduction Tri-Power throttle body assembly for 1959-66 Pontiac models with a 389 or 421 engine. This throttle body is manufactured out of Die Cast and features the carburetor shaft as well as the butterflies. The front and...
Reproduction of the original style fuel tank mounting straps that fit various 1964-1966 Buick, Chevrolet, Pontiac, and Oldsmobile mid-size, and full size models as listed (except station wagon). Each strap is manufactured in...
Reproduction of the original style fuel tank mounting straps that fit various 1964-1966 Buick, Chevrolet, Pontiac, and Oldsmobile mid-size, and full size models as listed (except station wagon). Each strap is manufactured in...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
Reproduction fuel tank for 1964 Tempest, Lemans, and GTO coupe or sedan models. This reproduction fuel tank is manufactured in quality stamped steel featuring a Zinc coating for rust and corrosion prevention. This is a 20...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
New reproduction Tri-Power carb top plate air horn 1964-66 GTO, LeMans, Tempest, Grand Prix and Bonneville with Tri-Power 389 engine. Finding these Tri-Power carburetor parts can be very hard to find. We now have the upper...
This is a new base plate assembly for all 1961-66 Tri-Power end carburetors for Pontiac GTO, LeMans, Tempest, Grand Prix and Bonneville. Also works on 1966 Oldsmobile Cutlass Tri-Power with 400 engine and Pontiac models with...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 100 GPH - 7 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 140 GPH - 9 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...