Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1964-66 Ford Mustang; Niterne Gas Tank Kit; With 5/16" Fuel Sending Unit; With Drain Plug
OER Authorized niterne steel reproduction gas tank kit comes with fuel tank, sending unit retaining lock ring and o-ring gasket, fuel sending unit, fuel filler neck, filler neck hose, hose clamps, filler neck screws, tank...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
1964-68 Ford Mustang; Fuel Tank Sending Unit; without Low Fuel Warning; 5/16"
Reproduction fuel tank sending unit for 1964-68 Ford Mustangs and other various models. The most accurate reproduction fuel tank sending unit in the industry, with original design brass float and filter. This unit monitors...
1964-68 Mustang, Cougar; Accelerator Linkage; V8 with Automatic Transmission
Reproduction of the original accelerator linkage designed for use with 1966-68 V8 Mustangs or 1967-68 V8 Cougar equipped with automatic transmission. This linkage connects your accelerator pedal to the accelerator rod. Mounts...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1948-86 Ford; Fuel Tank Sending Unit Brass Float; Various Models
Reproduction of the original style and correct brass float for use with various 1948-86 Ford and Mercury models as listed below. This sending unit brass float is desirable for its long-lasting dependability as it lasts much...
Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
1964-66 Ford Mustang; Niterne Gas Tank Kit; With 5/16" Fuel Sending Unit; Without Drain Plug
OER Authorized niterne steel reproduction gas tank kit comes with fuel tank, with retaining ring, 5/16" sending unit, filler neck, hose, clamps, tank screws, hardware and gasket. Offers precise fit and superior corrosion...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 100 GPH - 7 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 140 GPH - 9 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
Stainless steel reproduction of the fuel tank sending unit featuring the original design with a brass float, O-ring, and filter that replicate the original in appearance and functionality. This unit monitors the fuel level in...
Fuel Tank Sending Unit; 5 Hole; "Universal" 240-33 Ohm; For Many Aftermarket Gauges
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...