Upholstery Installation and Padding Kit; for Rear Bench Seat; 30" x 72" x 1.5" Rolls; Qty of 4
Reupholstery padding kit for rear bench seat. Comes with material to insulate and pad the seat frame before installing new upholstery. NOTE: Hog rings are required when installing new upholstery. Available separately. Refer...
Universal 9" Windshield Mount Rear View Mirror; Polished Ball Milled Billet Aluminum
Add a custom look to the interior with this fully polished and machined billet aluminum inner mirror. Since you spend most of your time inside your vehicle, why not get rid of your cheap looking original mirror and replace it...
Reproduction outer grill assembly for 1964-66 Chevrolet pickup trucks. Manufactured to factory specifications, each reproduction grill features the wording "CHEVROLET" in block lettering across the top bar of the grill....
Electric Vacuum Pump Set For Power Brakes - Universal Fit
It takes 16" of Hg vacuum to properly activate your vehicle's power brake booster. Sometimes, big-cammed or supercharged engines don't create enough vacuum to operate the booster, making it more difficult to stop. This vacuum...
Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Barrel Nut, Fits 5/32" Emblem Stud, Fits 7/32" Hole, Spring Steel, Black Phosphate Coated
Replacement barrel nuts used on various GM vehicles. The barrel nut is a push on style versus the original thread cutting pal nut, which will not require the removal of body panels for emblem installation. Simply install each...
1965-86 GM; Interior Door Panel Clip; White Nylon; Each
This special nylon clip is designed to attach to the cardboard backing on standard style interior door panel for various models. Once installed, the panel is pushed directly into the door frame and the clips hold the panel to...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
Headlamp Adjusting Screw ; For GM Models ; 1/4"-28 x 2"
Reproduction of the headlamp adjustment screw required for a wide variety of GM models including 1965-75 Impala, Biscayne, Bel Air and Caprice models. This 1/4"-28 adjustment screw comes zinc plated for corrosion resistance...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
OER Tri-Stic Retractable Pen with Black Ink
Ever wonder where all your pens go? Why not stock up on this eye catching inexpensive OER® black and yellow retractable pen.
Highly visible, quality lanyards are just what you need for any trade show event or car show. Features the bright OER® logo printed on both sides of 3/4" wide sublimation polyester. Includes an attached O-ring that will...
1962-71 GM Headlight 1/4"-28 x 1" Adjustment Screw with Nylon Nut
Original self-retaining nylon nut and 1/4"-28 x 1" screw assembly used for headlamp beam adjustment on 1962-71 GM models. This nut and screw mounts directly to the headlamp housing to enable the headlamp beam to be aimed...
1962-84 GM; Windshield Washer Jar Cap; Various Models
Reproduction of the original windshield washer jar cap designed for use on a variety of GM models including 1967-1974 Camaro. Manufactured in durable injection-molded ABS, this cap replicates the original design and includes...
This soft key tag is made of a sturdy material that is thick yet pliable, and comes with a spiral key ring.
1955-80 GM; Bolt, Pointed Tip; with Hex Washer Head, 5/16-18 X 1-1/4"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
OER® reproduction of the original headlamp adjusting spring designed for use on various GM models. This headlamp spring is used to adjust the headlight beam to the proper alignment. Applications: 1973-1974 Buick Apollo...
1962-1977 GM; Windshield Washer Jar Bracket; Various Models
OER® replacement of the original windshield washer jat bracket designed for use on various 1962-77 GM models as listed. This bracket is manufactured in stamped steel and features an EDP coating for rust resistance. This...
1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...