1961-68 GM Car; Various Models; Fuel Tank to Filler Neck Hose; 1-7/8 ID x 3 Long
Reproduction fuel tank to filler hose that seals the inlet filler neck to the tank stub neck. This hose will eliminate gas fumes from entering in the interior or trunk area when properly installed. Produced with correct high...
1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1961-64 Impala, Bel Air, Biscayne; Fuel Tank Mounting Brace; Each
Reproduction gas tank mounting brace for 1961-64 Impala, Bel Air, and Biscayne models. This brace attaches to the bottom of the trunk floor to support the gas tank. The gas tank mounting strap attaches to this brace....
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Reproduction fuel tank sending unit for 1961-64 Chevrolet Impala. Bel Air, and Biscayne models except station wagon. Each fuel sending unit is manufactured in quality steel to resist corrosion within your fuel tank. Provides...
1961-64 Impala, Bel Air, Biscayne; Fuel Tank Sending Unit; 5/16"; Except Station Wagon
Reproduction fuel tank sending unit produced with original design for an authentic fit and genuine appearance. Each sending unit includes the sender, gasket, filter, and a brass float as original. This unit monitors the fuel...
1964 Impala, Bel Air, Biscayne; Fuel Tank Filler Neck; Gray Primer; Except Station Wagon Models
Reproduction of the original fuel tank filler neck designed for use with 1964 Impala, Bel Air, and Biscayne models (except station wagons). Each neck is manufactured to factory dimensions and replaces the original exactly....
Reproduction of the original fuel tank mounting straps designed for use with 1961-1964 Impala, Bel Air, and Biscayne models (except station wagon). Each strap is manufactured in quality stamped steel and galvanized for long...
1964 Impala, Bel Air, Biscayne; Fuel Tank Filler Grommet; Each
Reproduction of the original fuel tank filler grommet designed for use with 1964 Impala, Bel Air, Biscayne, 1964-67 El Camino, Chevelle, and Malibu station wagon models. Grommets are manufactured to correct dimensions...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
Correct reproduction of the original fuel tank designed for with 1961-64 Chevrolet Impala, Bel Air, Biscayne models (except station wagon). This reproduction fuel tank is manufactured in stainless steel replicating the...
1961-64 Impala, Bel Air, Biscayne; NiTerne Coated Fuel Tank; with Flange; 20 Gallon
Reproduction of the original fuel tank designed for use with 1961-64 Chevrolet Impala, Bel Air, and Biscayne models (except station wagon). This reproduction fuel tank is manufactured in quality stamped steel featuring a...
Reproduction of the original fuel tank designed for use with 1961-64 Chevrolet Impala, Bel Air, and Biscayne models (except El Camino, station wagon). This reproduction fuel tank is manufactured in quality stamped steel...