1961-68 GM Car; Various Models; Fuel Tank to Filler Neck Hose; 1-7/8 ID x 3 Long
Reproduction fuel tank to filler hose that seals the inlet filler neck to the tank stub neck. This hose will eliminate gas fumes from entering in the interior or trunk area when properly installed. Produced with correct high...
1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
1961-64 Impala, Bel Air, Biscayne; Fuel Tank Sending Unit; 5/16"; Except Station Wagon
Reproduction fuel tank sending unit produced with original design for an authentic fit and genuine appearance. Each sending unit includes the sender, gasket, filter, and a brass float as original. This unit monitors the fuel...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
1955-86 Chevy, GMC, Pontiac; Fuel Pump Push Rod; Small Block / Big Block
Reproduction fuel pump push rod for 1955-86 Chevrolet, GMC, and Pontiac models. Fits Chevrolet small block, big block, and Pontiac V8 engines. 5-3./4" long x 1/2" dia. {fitment}
Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors
Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...
1962-81 GM; Fuel Tank Sending Unit Lock Ring; Small; 1-15/16"; Various Models
Correct reproduction fuel tank sending unit locking ring which secures the fuel tank sending unit to the gas tank. Replaces the original ring which are commonly destroyed when being removed. This ring helps to seal the...
1955-69 GM; Accelerator Pedal Firewall Bushings; 1/2" Long, 5/16" I.D.; Pair
Reproduction accelerator firewall bushings for various 1955-69 GM models. These bushings are required to install the accelerator rod support correctly. They help to eliminate excessive play in the gas pedal pad while...
1958-71 GM; Accelerator Pedal Ball Stud Pivot; 1/4"-20 x 1-1/2"; Each; Various Models
Reproduction factory ball stud pivot for various GM models. 1/4"-20 x 1-1/2". Accelerator pedal ball studs can break after many years of use and will need to be replaced. Check your stud for wear when replacing the gas pedal...
Reproduction of the original style stamped steel accelerator pedal pad to rod support unit. This steel reproduction is manufactured to replicate the original in appearance, design and functionality. Includes correct style...
1955-81 Retainer Clip; Trans Control Rod, Clutch Push Rod, Throttle Rod Swivel
OER® reproduction clip for a variety of different parts on 1955-81 GM vehicles. This clip was used to attach the throttle valve control rod, throttle lever rod swivel, and the upper and lower clutch push rods. Use as...