Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1963-72; Chevrolet Bow Tie Outer Door Mirror; with Mounting Hardware
Reproduction outer door mirror for various 1967-72 Chevrolet models. Each mirror is manufactured in die-cast zinc to factory specifications. Will fit and install as original. Features the Bow Tie emblem engraved on the rear...
1962-1977 GM; Windshield Washer Jar Bracket; Various Models
OER® replacement of the original windshield washer jat bracket designed for use on various 1962-77 GM models as listed. This bracket is manufactured in stamped steel and features an EDP coating for rust resistance. This...
1962-72 Chevrolet/Pontiac; OE Style Firewall Pad Fastener; Plastic; 7/16" X 1.50"; Various Models
Correct reproduction plastic firewall pad fastener for various GM models including 1967-69 Camaro, 1967-69 Firebird, 1962-72 Nova and 1962-69 Impala models. These fasteners are required to allow the firewall pad to attach...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1966-74 GM; Outer Door Mirror; Round; with Ribbed Base; Hardware Included; "Show Quality"
Reproduction of the original outer door mirror designed for use with various 1966-74 GM models. Original style replacement outer door mirror manufactured in high quality zinc die-cast with excellent chrome finish. Each mirror...
1959-80 AMC, GM, Ford, Mopar; Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
1963-67 Chevrolet, Oldsmobile, Pontiac; Hood Hinge Assembly; RH Passenger Side
Reproduction hood hinge assembly for various 1963-67 GM models. Each hood hinge is manufactured from stamped steel to factory specifications assuring a quality replacement. Features correct mounting points for ease of...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
High-quality reproduction of the stainless steel "Aero" Anti-Wind-Lift wiper blades designed to fit 7mm wide bayonet-style wiper arms. Popularized in the 1960s and 1970s to combat wind lift at high speeds, these 15" wiper...
1964-67 Chevrolet El Camino; Back Glass; Smoke Gray Tint
Reproduction back window glass for 1964-67 Chevrolet El Camino models. Replace scratched or damaged original with this OEM quality replacement. Each glass is professionally packed with extra care to prevent damage during...
1964 Chevelle, Malibu, El Camino; Front Bumper Bracket Set; 4-Pieces
Reproduction front bumper bracket set for 1964 Chevrolet Chevelle, Malibu, and El Camino models. Manufactured in stamped steel to factory specifications, each bracket replicates the original design for proper fit, strength,...
1964-66 El Camino; Tailgate Skin; Replaces GM# 4883711
This tailgate skin is a high quality reproduction part built to replace the original outer tailgate panel on 1964-66 El Camino models. Each tailgate skin is manufactured to factory specifications featuring the correct...
Correctly reproduced glass windshield washer bottle that was common in various 1955-72 General Motors vehicles. Each bottle is manufactured in the correct factory configuration that replaces the old or missing original...
1963-69 Buick, Chevrolet, GMC, Oldsmobile, Pontiac; Windshield Wiper Motor; 1 Speed; Brand New
Brand New Reproduction wiper motor built using the industry's most advanced engineering technology. Core shortages and low availability have made our brand new replacement wiper motors the high quality, low cost alternative...
Factory-style reproduction front door latch assembly for various GM models. Engineered to original specifications to restore smooth, positive latching and proper door alignment, this complete assembly replicates the factory...
1964-67 Chevrolet El Camino; Door Glass; RH; Smoke Gray Tint
This premium reproduction RH door glass is designed for 1964-67 Chevrolet El Camino models. Manufactured in smoke gray tinted glass to factory specifications for a precise fit. Expertly crafted to deliver both durability and...
Ford, GM, Mopar; Windshield Wiper Blade Refill; 16"; Pair
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
1964-67 Chevrolet El Camino; Back Glass; Light Green Tint
Reproduction back window glass for 1964-67 Chevrolet El Camino models. Replace scratched or damaged original with this OEM quality replacement. Each glass is professionally packed with extra care to prevent damage during...
Reproduction license plate rubber bumpers for various GM models including 1967-68 Camaro front or rear. Each bumper replicates the original in fit and appearance. Will replace the original worn out or missing original rubber...
Factory-style reproduction front door latch assembly for various GM models. Engineered to original specifications to restore smooth, positive latching and proper door alignment, this complete assembly replicates the factory...
1964-67 Chevrolet El Camino; Door Glass; RH; Clear
This premium reproduction RH door glass is designed for 1964-67 Chevrolet El Camino models. Manufactured in clear glass to factory specifications for a precise fit. Expertly crafted to deliver both durability and OE...
1960-84 Windshield Wiper Blade; 16" Trico; Rainbow Type; 1/4" Bayonet Connector; Matt Stainless
Reproduction of the original Trico Rainbow Type wiper blade designed for various models originally equipped with Trico blades. Each wiper blade will replace the original and offer years of service. Each blade comes complete...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
1967-69 Camaro, Firebird; Convertible Top Boot Interior Snaps; with Screws; 4 Piece Set
Reproduction convertible top boot snap and screw set for 1967-69 Camaro and Firebird models and any other vehicle that requires a screw-on style snap. These snaps are used to secure the convertible top to the inner rear...
Tapping Screw; #8 x 1"; Phillips Pan Head; A/AB; Black Oxide
This reproduction screw can be used on many applications where a #8 X 1" phillips pan head Black Oxide plated tapping screw is needed. Sold individually.
Reproduction zinc-plated bumper bolt with a polished stainless steel capped head for a variety of GM, Ford and Mercury applications including 1958-66 Chevrolet, 1965-68 Ford Mustang, 1960-67 Ford Falcon and 1960-65 Mercury...
Reproduction 16" windshield wiper blade for a variety of GM vehicles that require a 16" side lock blade. Each blade is manufactured in stainless steel and finished in satin silver as original. Fits the side lock style...
Reproduction hood latch striker catch assembly for 1964 Chevrolet full size passenger car and 1964 Chevelle, Malibu, and El Camino models. This high quality hood latch catch assembly is manufactured to factory specifications...
This premium reproduction RH vent glass is designed for 1964-67 Buick Special/Skylark, Chevrolet Chevelle, Oldsmobile Cutlass, Pontiac Tempest, and El Camino models. Manufactured in smoke gray tinted glass to factory...
This premium reproduction LH vent glass is designed for 1964-67 Buick Special/Skylark, Chevrolet Chevelle, Oldsmobile Cutlass, Pontiac Tempest, and El Camino models. Manufactured in smoke gray tinted glass to factory...
Spring Steel Rod Clip, for Carburetor, Door, Tailgate; LH Driver Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...
1964-98 GM; Door Lock Striker Bolt Washer Shim ; 1.25MM Thick ; Each; Various Models
Reproduction of the original door striker bolt shim manufactured in die-stamped steel and finished in clear zinc coating. Used to correctly position the door striker bolt for proper alignment with the door latch assembly. Use...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
1967-81 GM; Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; for Hood Hinges; 8 Piece Set; Various Models
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
This premium reproduction RH vent glass is designed for 1964-67 Buick Special/Skylark, Chevrolet Chevelle, Oldsmobile Cutlass, Pontiac Tempest, and El Camino models. Manufactured in light green tinted glass to factory...
This premium reproduction LH vent glass is designed for 1964-67 Buick Special/Skylark, Chevrolet Chevelle, Oldsmobile Cutlass, Pontiac Tempest, and El Camino models. Manufactured in light green tinted glass to factory...
Hex Washer Head Spin Lock Bolt; 5/16" X 18 X 1-1/4"; Phospate Coating" Each
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished iin a black phospate coating for an authentic original appearance and corrosion resistance. Sold individually. Use as required. Product Specifications:...
Bumper Bolt; Stainless Steel Cap; Flat Head; 3/8"-16X 15/16"; Package of 25
Package of 25 reproduction bumper bolts that measure 7/16-14 x 1-1/2" with a stainless steel cap and round head. Willl fit a wide variety of vehicles including 1957-72 Ford F-Series Truck and many other Ford Motor Company...
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
Reproduction of the original Trico Style wiper blade refill designed for use on the various models that require a 16" Trico style rainbow type wiper blade. Each wiper blade assembly will replace the original and offer years...
#10-24 x 1"; Phillips Oval Head Head Machine Screw; Stainless Steel
Stainless Steel Phillips #10-24 x 1" Oval Head Head Machine Screw. Sold individually. Specifications: Thread Diameter : 10-24 Length : 1" Head Style : Phillips Oval Head Size : Std Material : 18-8 Stainless Steel
Plastic Retainer; Push-In Type Rivet; 7/8" Head Diameter; 1-3/64" Stem Length; For 1/2" Hole
Reproduction push-in retainer designed to attach the front urethane bumper cover to the impact bar. Push-in style. 28.2mm long. Manufactured in durable ABS black plastic material. Sold individually. Use as required. Replaces...
Hex Washer Head Spin Lock Bolt; Phospate Coating; 5/16" X 18 X 1-1/4"; Set of 24
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished in a black phospate coating for an authentic original appearance and corrosion resistance. Set of 24. Use as required. Product Specifications: Thread...
1964-72 Chevrolet Chevelle, El Camino, 1970-72 Monte Carlo; Fender To Core Support Brace; Pair
Reproduction fender to radiator core support braces for 1964-72 Chevelle, El Camino, Malibu and 1970-72 Monte Carlo. Without these braces the fender will wobble around and cause damage to the fender. These are commonly rusty...
U-Nut Set; M6 - 1.0; Panel Range.030" to.160"; Black Phosphate; 25 Piece Set
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160"). Set of 25 u-nuts. Specifications: OE #: 11503957 Quantity:...
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...
Installation hardware set for various 1985-92 Camaro models including IROC-Z models. Each set includes 18 of reproduction # 11508023 bolt. Specifications: Quantity: Set of 18 Class: 9.8 Color: Black Phosphate Material: Steel...
Tapping Screw; Hex Washer Head; #8-18 x 1/2" Long; Black Oxide
Hex, washer head #8-18 x 1/2 tapping screw, in phosphate and oil coating for various applications including mounting grill to various classic vehicles Screw Specs: Description : Tapping Screw Screw Size : #8 Length : 1/2"...
Hex Bolt; 1/2"-13 x 4" LG; Gd 8; Yellow Dichromate
Hex Bolt; 1/2"-13 x 4" Lg; Gd 8; Yellow Dichromate Application 1973-1980 Chevrolet/GMC Radiator Core Support; STD Cab 1/2 & 3/4 Ton 1973-1980 Chevrolet/GMC Radiator Core Support; Crew Cab 3/4 Ton 1973-1980 Chevrolet/GMC Front...
1955-74 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 3/4"; Black Phosphate; 10 Piece Set
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. The OER® Authorized logo represents...
Bolt, 1/4-20 x 1-3/16" Dog Point Tip With Free Spinning Washer, Black Phosphate, 10 Piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
Bolt, 5/16-18 x 1" Pointed Tip With Hex Washer Head, Black Phosphate, 10 Piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
Bolt, 5/16-18 X 7/8" Pointed Tip With Free Spinning Washer, Black Phosphate, 10 piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate, 10 Piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...