1961-68 GM Car; Various Models; Fuel Tank to Filler Neck Hose; 1-7/8 ID x 3 Long
Reproduction fuel tank to filler hose that seals the inlet filler neck to the tank stub neck. This hose will eliminate gas fumes from entering in the interior or trunk area when properly installed. Produced with correct high...
1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1961-64 Impala, Bel Air, Biscayne; Fuel Tank Mounting Brace; Each
Reproduction gas tank mounting brace for 1961-64 Impala, Bel Air, and Biscayne models. This brace attaches to the bottom of the trunk floor to support the gas tank. The gas tank mounting strap attaches to this brace....
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
1955-70 Impala, Full Size; Fuel Tank Mounting Strap Hardware Set; 6-Pieces
Use proper mounting hardware to make your fuel tank installation job easier. This hardware set is the correct replacement fuel tank strap bolt set for 1955-70 full size Chevrolet models including 150, 210, Bel Air, Impala,...
1947-76 GM, Chrysler, Dodge, Plymouth; Brass Fuel Tank Sending Unit Float
Reproduction brass fuel sending unit float for various 1947-76 General Motors, and Chrysler, Dodge, Plymouth models. If your fuel gauge isn't reading correctly, it may be the fuel sending unit float. The original OE float may...
1961-1963 Impala, Bel Air, Biscayne; Fuel Tank Filler Neck; Gray Primer; Except Station Wagon Models
Reproduction of the original style steel fuel tank filler neck designed for use with 1961-1963 Impala, Bel Air, and Biscayne models. Each filler neck assembly is manufactured in quality stamped steel and features a gray...
1961-64 Impala, Bel Air, Biscayne 6 Pass Station Wagon; Fuel Tank Sending Unit; with 5/16" Line
Reproduction of the original fuel tank sending unit designed for use with 1961-64 Chevrolet Impala, Bel Air, and Biscayne station wagon models with 5/16" line. Each sender is produced in quality steel to resist corrosion...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors
Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...
1962-81 GM; Fuel Tank Sending Unit Lock Ring; Small; 1-15/16"; Various Models
Correct reproduction fuel tank sending unit locking ring which secures the fuel tank sending unit to the gas tank. Replaces the original ring which are commonly destroyed when being removed. This ring helps to seal the...
1955-69 GM; Accelerator Pedal Firewall Bushings; 1/2" Long, 5/16" I.D.; Pair
Reproduction accelerator firewall bushings for various 1955-69 GM models. These bushings are required to install the accelerator rod support correctly. They help to eliminate excessive play in the gas pedal pad while...
1942-86 GM; Fuel Sending Unit Filter Strainer; for 3/8" Pickup Tube
Correct reproduction of the original fuel tank float strainer designed for use with various 1955-85 GM car and truck models. This filter screen will keep dirt and other elements from clogging or entering the fuel system....
Fuel Sending Unit Filter Strainer; For 5/16" Pickup Tube
Correct OER® reproduction of the original fuel tank float strainer designed for use with various 1942-85 GM, Chrysler, Dodge, Plymouth models as listed below. This filter will keep dirt and other elements from clogging or...