1962-67 Chevy II, Nova; Mono Rear Leaf Springs; Pair; Made in the USA
These reproduction rear leaf springs are engineered for an exact, direct replacement of the original mono leaf springs used on 1962-1967 Chevy II and Nova models. Each spring is manufactured to factory specifications and...
1962?1967 Chevrolet Chevy II, Nova; Crossmember Kit Mustang II IFS Front End
Upgrade the factory front suspension of your 1962?67 Chevy II Nova with a high-performance Mustang II front end. This heavy-duty crossmember, crafted from durable 7-gauge steel, is engineered to accept a no-strut Mustang II...
1959-81 GM; Coil Spring Spacer; 9/16" Thick; EPDM Rubber; Each
Reproduction of the original 9/16" coil spring spacer designed for use on various GM models. Manufactured from durable EPDM rubber, this spacer was originally installed to correct uneven ride height on vehicles that did not...
1963-67 Chevy II, Nova Front End Suspension Rebuild Kit; with Inner& Outer Tie Rod Ends
This kit includes a comprehensive assortment of front end components engineered to renew worn out original suspension parts. Designed to restore proper handling, improve steering control, and reduce uneven front tire wear,...
1962-67 Chevy II / Nova; Lower Control Arm Ball Joint; with Hardware
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
1962-67 Chevy II / Nova; Upper Control Arm Ball Joint; with Hardware
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
1962-69 Chevy II Nova 1967-69 Camaro Firebird; Sway Bar Bushings; Original Design
Reproduction of the original sway bar bushings designed for use with 1962-69 Chevy Nova, 1967-69 Camaro and Firebird models. Each bushing is manufactured in quality EPDM rubber replicating the original in design, dimensions,...
1962-67 Chevy II, Nova; Disc Brake Spindle Set; Stock Height; LH And RH; Pair
Converting your drum brake car to disc brakes will drastically reduce the braking effort needed to stop your vehicle quickly and safely. When converting your 4-lug or 5-lug drum vehicle to disc brakes, you will need to change...
1962-67 Chevy II Nova; Strut Rod; with Hardware
Reproduction of the original strut rod designed for use on 1962-67 Chevy II Nova models. Manufactured to correct OE specifications for reliability and authenticity. Rods are 21-3/4" overall length, 5-5/8" thread length,...
Mustang II Top Spring Hat Set; For Weld-In Mustang II Front Suspension Conversion
Universal weld-in Mustang II upper crossmember spring hat set designed to be used when converting your vehicle to Mustang II style front suspension. Produced in heavy duty steel, tig-welded, and ready for you to weld into...
1962-67 Chevy II, Nova; Lower Control Arm Bushing; with Built-In Endcaps
Authentic reproduction of the original control arm bushing designed for use on the lower control arm for 1962-67 Chevrolet Chevy II models. Manufactured in steel clad rubber to be pressed into place. If your suspension...
1962-87 Buick, Chevrolet, Pontiac, Olds; Ball Joint Rivet Bolt Set; 24 Piece Set; Various Models
This rivet style bolt set attaches the ball joint to the upper control arm while providing the authentic appearance of factory installed rivets. Each bolt features a serrated locking rivet style head that prevents spinning...
1962-67 Chevy II, Nova; Front Eye Bolt; with Cupped Washer & Nut; Grade 8
Replacement front eye bolt kit with cupped washer and nut for 1962-1967 Chevy II and Nova rear leaf springs. This high quality kit includes a 7/16-20 x 5 1/8" Grade 8 hex shoulder bolt, a.57" x 2.50" x.46" cupped washer, and...
1960-96 Various GM Vehicles Camaro, Cutlass, Impala; Front Sway/Stabilizer Bar; Bushing WS6; 13/16"
New 13/16" sway bar bushing WS6 for heavy duty stamped bracket for various 1961-96 GM vehicles which includes Impala, Cutlass, Monts Carlo and Camaro. Manufactured to meet or exceed the OEM in both quality and fitment....
New 15/16" sway bar bushing WS6 for heavy duty stamped bracket for various 1961-96 GM vehicles which includes Impala, Cutlass, Monts Carlo and Camaro. Manufactured to meet or exceed the OEM in both quality and fitment....
1967-69 Camaro, Firebird; 1962-69 Chevy II Nova; Rear Leaf Spring Shackle; LH or RH; Each
This reproduction rear spring shackle is engineered for 1967-1969 Camaro and Firebird models and built to match the original in appearance, quality, and fit. Designed to OEM specifications, each shackle includes all required...
Reproduction molded rubber front coil spring insulator designed to mount between the coil spring and the frame on various 1949-2002 vehicles. This insulator prevents metal to metal contact, reducing noise, vibration, and...
Introducing the latest innovation in independent front suspension systems ? the Deluxe Nova IFS Crossmember. Engineered for performance and durability, this advanced front end kit is designed for builders who want the...
1963-67 Chevy II, Nova; Front End Suspension Rebuild Kit; with Outer Tie Rod Ends Only
This kit includes a comprehensive assortment of front end components engineered to renew worn out original suspension parts. Designed to restore proper handling, improve steering control, and reduce uneven front tire wear,...
Reproduction control arm bushing cap designed for use on 1962-1967 Chevy II and Nova front lower control arms, as well as 1963-1979 Corvette rear strut rods. This cap is essential for proper fitment when replacing lower...
1962-67 Chevy II, Nova; Front Coil Spring Perch Assembly; RH & LH; Pair
Reproduction of the original front coil spring perch bracket assembly designed for use on 1962-1967 Chevy II and Nova models. Each bracket is manufactured from heavy stamped steel to accurately replicate the original in both...
1974-78 Ford Mustang II, Pinto; Spindle Set; Forged Steel; Stock Height; Pair
Our Mustang II stock height front spindles are built from forged steel and heat treated for superior strength. Will fit 1974-78 Ford Mustang, 1974-80 Ford Pinto, and 1975-80 Mercury Bobcat. Mustang II style spindles are also...
Grade 5, size 7/16-14 USS hex nut, in zinc plated finish. Sold individually. Specifications: Screw Size : 7/16-14 Across Flats : 11/16" Grade : 5 S.A.E. Standard : J995 Finish : Zinc Proof Load : 120000 Rockwell Hardness :...
1962-67 Chevy II Nova; Upper Control Arm; with Ball Joint and Bushing; LH or RH
Reproduction upper control arm, shaft and ball joint assembly for 1962-67 Chevrolet Chevy II/Nova and Pontiac Acadian models. Each control arm assembly is manufactured in quality stamped steel to the factory configuration...
1962-67 Chevy II, Nova; Front Sway Bar; 1" diameter; with Bushings & Hardware
Front sway bar kit for 1962-1967 Chevrolet Chevy II and Nova models equipped with a 1" front sway bar. Each sway bar is manufactured to correct factory specifications, accurately replicating the original in both design and...
1974-78 Mustang II; Front Sway Bar Kit; 3/4" ; 43-1/4" Wide; for Standard Crossmember
Replacement 3/4" sway bar kit for hot rods and custom trucks equipped with standard width crossmember Mustang II front suspension systems. This sway bar is engineered to reduce body roll, under steer, and over steer during...
1962-67 Chevy II, Nova; Front End Bushing Set; 8 Piece Set
Control arm ball joints and bushings endure constant stress over decades of driving, often leading to excessive play in the front end and unsafe handling conditions. If your suspension rattles, clunks, or feels loose when...
1962-67 Chevy II, Nova; Shock Tower; Each; EDP Coated
Shock tower for 1962-1967 Chevrolet Chevy II and Nova models. Each tower is manufactured from stamped steel to original equipment specifications, providing an authentic reproduction of the factory shock tower. An excellent...
Front Boxing Plate set designed for use when boxing in the frame. These boxing plates weld into place to box the frame in critical front suspension attachment points when converting to a Mustang II style IFS - Independant...
1967-69 Camaro, Firebird, 1962-69 Chevy II Nova; Leaf Spring Shackle Bushing Set; 8 Piece Set
Reproduction of the original style leaf spring shackle bushings for use with 1967-69 Camaro, Firebird, and 1962-69 Chevy II and Nova models. Replace your cracked, shrunken or worn out shackle bushings and bring your rear...
1967-69 Camaro, Firebird, 1962-74 Chevy II, Nova; Mono Leaf Spring Pad Set; 4 Piece Set
Each pad is designed to insulate the contact area between the leaf spring and the mounting plate, reducing metal to metal contact, vibration, and noise. These pads help protect the spring assembly, maintain proper suspension...
Sway Bar Bracket; Tab Style; Universal; End Link to Lower Control Arm or Frame Rail, LH or RH
This universal sway bar end link bracket is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
This universal sway bar end link bracket set is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
1967-69 Camaro, Firebird, 1962-74 Chevy II, Nova; Rear Leaf Spring Pad; Upper; with Mono Leaf
Reproduction of the original mono leaf upper rear spring pad designed for use on various GM models. Each pad is manufactured to OE specifications using quality EPDM rubber compound for long lasting dependability. Always...
1962-67 Chevy II, Nova; Upper Control Arm Bushing; Each
Reproduction of the original style upper control arm bushing designed for use on 1962-67 Chevy II and Nova models. If your suspension rattles or makes noises when turning or going over bumps, it might be time to think about...
1962-67 Chevy II / Nova; Front Coil Spring Upper Seat Plate; Each; EDP Coated
Reproduction of the original upper seat plate designed for use with 1962-1967 Chevy II and Nova models. This seat plate supports the front coil spring and is essential for proper suspension function. Each plate is...
1962-81 GM; Rear Leaf Spring Front Eye Bracket Bolt ; Each; Various Models
Quality reproduction of the original rear spring eye bracket bolt designed to mount the leaf spring front eye bracket. Each bolt is case hardened for exceptional durability, strength, and long lasting performance. An ideal...
1962-70 Buick, Chevy; Pontiac, Oldsmobile; Control Arm Bumper; Rubber; Each; Various Models
Reproduction of the original control arm bumper designed for use on various GM models. Each bumper is manufactured to factory specifications in the correct configuration and includes a built in stud ensuring a perfect fit....
1962-74 Camaro, Firebird, Nova ; X body; Rear Leaf Spring Pad; Lower; with Mono Leaf; Each
Reproduction of the original lower mono leaf spring pad designed for use on various GM models. Each pad is manufactured to OE specifications using high quality EPDM rubber for long lasting durability and proper cushioning....
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate
Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...
1967-69 Camaro, Firebird, 1962-69 Chevy II / Nova; Rear Spring Shackle Bushing; Each
Reproduction of the original rear spring shackle bushing designed for use on various 1967-69 GM models. Manufactured is quality EPDM hard rubber replicating the factory original in quality and ftment. Replace your cracked,...
Emblem Installation Speed Nut Set ; 5/16" ; 8 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 8...
Emblem Installation Speed Nut Set ; 5/16"; 4 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 4...