Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
Reproduction of the original lower window channel for use with various 1961-64 Buick, Chevrolet, Pontiac, and Oldsmobile models. The door window glass rests in the channel assembly as it mounts to the regulator. Manufactured...
Correctly reproduced glass windshield washer bottle that was common in various 1955-72 General Motors vehicles. Each bottle is manufactured in the correct factory configuration that replaces the old or missing original...
1961-65 GM Full Size; Vent Window Regulator; Passenger Side; GM B Body Models
Reproduction of the original vent window requlator designed for use on various 1961-65 GM Buick, Chevrolet, Oldsmobile, and Pontiac full size models. Each regulator is designed and manufactured to replicate the original in...
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
Replace a broken or missing door window frame with this quality reproduction that is designed to replace your originals exactly. The door window frame helps support the glass when installed in the door. Glass not included....
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
1967-81 GM; Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; for Hood Hinges; 8 Piece Set; Various Models
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...
1955-74 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 3/4"; Black Phosphate; 10 Piece Set
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. The OER® Authorized logo represents...
1955-74 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 3/4"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a set of 10, refer to part...
Bumper Bolt with Stainless Steel Head; Zinc Plated; 7 /16"-14 x 1" Bolt with Hex Nut
Reproduction bumper bolt with hex nut manufactured in zinc plated material offering an authentic appearance and fitment. Measures 7/16" -14 x 1" and features a stainless steel cap. Head diameter 31/32". Each bolt will replace...