Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1961-62 Impala / Fullsize 4 Door Hardtop Smoke Back Glass
Replacing your original damaged or missing back glass will enhance your vehicle's appearance and safety by allowing you to see clearly. Don't settle for anything less than original quality glass when replacing the windows of...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
1959-72 Buick; Chevrolet; Oldsmobile; Pontiac; Trunk Lock Latch Assembly; Manual; Various GM Models
This OER® reproduction of the original manual trunk lid latch assembly. This correct reproduction installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Allows the trunk lid to lock...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
Reproduction of the original front windshield glass for use with 1961-62 Buick, Chevrolet, Pontiac, and Oldsmobile Full Size 2 & 4 door, sedan, hardtop, and station wagon models as listed. This windshield is manufactured with...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
High-quality reproduction of the stainless steel "Aero" Anti-Wind-Lift wiper blades designed to fit 7mm wide bayonet-style wiper arms. Popularized in the 1960s and 1970s to combat wind lift at high speeds, these 15" wiper...
Correctly reproduced glass windshield washer bottle that was common in various 1955-72 General Motors vehicles. Each bottle is manufactured in the correct factory configuration that replaces the old or missing original...
Reproduction of the original upper door hinge designed for use on 1961-64 Impala, Bel Air, Biscayne, and GM B-Body models. Sagging and worn door hinges can cause damage to doors, locks and hinge pillar sheet metal. Why go...
1961-65 GM Full Size; Vent Window Regulator; Passenger Side; GM B Body Models
Reproduction of the original vent window requlator designed for use on various 1961-65 GM Buick, Chevrolet, Oldsmobile, and Pontiac full size models. Each regulator is designed and manufactured to replicate the original in...
Ford, GM, Mopar; Windshield Wiper Blade Refill; 16"; Pair
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
New power window motor for various GM passenger car and truck models. Manufactured to factory specifications for an original fit and function. This original style power window motor was used in wide variety of GM models....
Reproduction of the original vent window assembly for use with 1961-62 Buick, Chevrolet, Cadillac, Pontiac, and Oldsmobile full size models as listed below. Each vent assembly is manufactured to correct factory specifications...
Reproduction of the original vent window assembly for use with 1961-62 Buick, Chevrolet, Cadillac, Pontiac, and Oldsmobile full size models as listed below. Each vent assembly is manufactured to correct factory specifications...
1961-62 GM Front Door Latch; LH ; Full Size Models
OER® Authorized reproduction of the original door latch assembly designed for use on 1961-62 GM B-Body 2 door hardtop and convertible models. Door latches are manufactured ro factory specifications replicating the...