1959-81 GM; Coil Spring Spacer; 9/16" Thick; EPDM Rubber; Each
Reproduction of the original 9/16" coil spring spacer designed for use on various GM models. Manufactured from durable EPDM rubber, this spacer was originally installed to correct uneven ride height on vehicles that did not...
1958-64 Impala; Lower Control Arms; Rubber Bushings; Pair
New stock style lower control arms designed for use with 1958-64 Chevrolet Impala, Bel Air, Biscayne, and full size models. Includes both RH and LH lower control arms with cross shafts, bushings, and ball joints...
1958-64 Impala, Bel Air, Biscayne; Front Disc Brake Spindles; 2" Drop; Pair
These 2 inch drop spindles are engineered for lowering your disc brake converted vintage Chevy a full 2 inches while maintaining proper steering geometry and smooth suspension operation. Precision cast from high quality...
1958-62 Impala, Bel Air, Biscayne; Front End Suspension Rebuild Kit
1958-62 Chevrolet Impala front end rebuild kit providing nearly everything required to restore a worn out suspension to smooth, dependable performance. This comprehensive assortment of components is engineered to replace aged...
Quality reproduction rear control arm for 1960-72 Chevrolet and GMC truck models equipped with rear coil springs. Commonly referred to as a trailing arm, this component mounts between the rear axle housing and the center...
1960-72 Chevy, GMC Pickup, Blazer, Jimmy, Suburban; Rear Control Arm; LH Driver Side; EDP Coated
Quality reproduction rear control arm for 1960-72 Chevrolet and GMC truck models equipped with rear coil springs. Also known as a trailing arm, this component mounts between the rear axle housing and the center crossmember to...
1960-72 Chevy, GMC Pickup, Blazer, Jimmy, Suburban; Rear Control Arm; RH Passenger Side; EDP Coated
Quality reproduction rear control arm for 1960-72 Chevrolet and GMC truck models equipped with rear coil springs. Also known as a trailing arm, this component mounts between the rear axle housing and the center crossmember to...
Reproduction lower control arm bushings for 1955-64 Chevrolet Bel Air, Impala, Corvair, and Full Size models. Each bushing is manufactured to factory specifications. Add new life to your suspension by replacing the old...
1958-64 Impala, Bel Air, Biscayne; Front Tubular Lower Control Arms; RH & LH; Pair
These performance tubular lower control arms are engineered to accept standard coil springs, coil over shocks, or air bag shock systems, making them a versatile upgrade for a wide range of suspension setups. Each arm comes...
1958-64 Impala, Bel Air, Biscayne; Front Tubular Upper Control Arms; RH & LH; Pair
Reproduction of the original upper tubular upper control arms designed for use with 1958-64 Impala, Bel Air, Biscayne, and Full Size Chevrolet models. These tubular style upper control arms change the way the car drives and...
1958-64 Impala, Bel Air, Biscayne; Front Sway Bar;1" Dia.; with Hardware
Front sway bar kit for 1958-1964 Chevrolet Impala, Bel Air, and Biscayne models. This sway bar kit is engineered to reduce body roll, under steer, and over steer during cornering, resulting in improved stability, enhanced...
1958-64 Impala, Bel Air, Biscayne; Rear Sway Bar Kit; 1" Diameter; with Mounting Hardware
These sway bars are engineered to reduce body roll, under steer, and over steer during cornering, resulting in improved vehicle stability, enhanced handling response, and greater overall control. Designed to provide these...
1958-64 Impala / Full Size Upper Control Arm; RH
This is a reproduction of the right hand upper control arm used on 1958-64 full size models. For left hand side use Part # A1000. Note: This is the control arm only, ball joints, bumpers, shafts and bushings are sold...
Reproduction bushing for the rear panhard rod on 1959-64 Chevrolet Impala, Bel Air, Biscayne models, and for the rear strut rod on 1959-62 Corvette. If your full size Chevrolet or Corvette model is feeling loose around...
1958-64 Impala, Bel Air, Biscayne; Upper Control Arm Shaft Set; Pair
Reproduction of the original style upper control arm shafts for 1958-1964 Chevrolet Impala, Bel Air, and Biscayne models. Each set is engineered to restore proper suspension alignment and factory-correct performance while...
Mustang II Top Spring Hat Set; For Weld-In Mustang II Front Suspension Conversion
Universal weld-in Mustang II upper crossmember spring hat set designed to be used when converting your vehicle to Mustang II style front suspension. Produced in heavy duty steel, tig-welded, and ready for you to weld into...
1958-64 Impala, Bel Air, Biscayne, 1965-82 Corvette; Lower Control Arm Shaft; LH or RH; Each
Quality reproduction lower control arm cross-shaft for various 1958-1964 Chevrolet Impala, Bel Air, Biscayne, and 1963-1982 Corvette models. Each shaft is manufactured from high quality stamped steel and built to original...
1960-62 Chevy, GMC C10 Pickup, Suburban; Lower Ball Joint; Each
1960-62 Chevrolet C10 and GMC 1000 Series lower ball joint designed to restore proper steering control and front suspension stability. A worn ball joint can create steering slop, poor alignment, and unsafe handling...
1958-64 Impala, Bel Air, Biscayne, El Camino; Lower Control Arm Plate Set; with Screws and Washers
Reproduction of the original lower control arm plate for use with 1958-64 Chevrolet Impala, Bel Air, and Biscayne models. Each set includes a forged lower control arm plate with Grade-8 screws and washers. 2 sets required per...
1953-62 Chevy Corvette; Leaf Spring Shackle; with Bushings; LH or RH; Per Side
Reproduction rear leaf spring shackle with bushings for 1953-62 Chevrolet Corvette models. Each shackle includes 8 total pieces to fit either the LH or RH side. Comes with the bushings and installation hardware. Two are...
1960-72 Chevrolet, GMC Pickup Truck; Single Coil Spring Retainer; Upper & Lower; Each
Reproduction of the original single coil spring retainer for 1960-1972 Chevrolet and GMC trucks. Each retainer cup is manufactured from stamped steel to original factory specifications and features the correct contours for an...
New reproduction of the OEM 1958-88 GM heavy duty front sway bar/stabilizer bar bushing WS6 for multiple GM vehicles including Chevrolet Chevelle, Buick Skylark, Oldsmobile Cutlass and Pontiac GTO models with 7/8" diameter...
Reproduction molded rubber front coil spring insulator designed to mount between the coil spring and the frame on various 1949-2002 vehicles. This insulator prevents metal to metal contact, reducing noise, vibration, and...
1958-64 Impala, Bel Air, Biscayne; Upper Control Arms; Rubber Bushings; Pair
New stock style upper control arms designed for use with 1958-64 Chevrolet Impala, Bel Air, Biscayne, and full size models. Includes both RH and LH upper control arms with cross shafts, bushings, and ball joints...
1955-70 Full Size Chevy; Upper Ball Joint; with Hardware; RH or LH
Reproduction of the original upper ball joint designed for use with 1955-70 Chevy full size models including 1955-57 Chevy, and 1958-70 Impala, Bel Air, Biscayne, and Caprice models. Control arm ball joints take a beating...
Quality reproduction rear control arm for 1960-72 Chevrolet and GMC truck models equipped with rear coil springs. Commonly referred to as a trailing arm, this component mounts between the rear axle housing and the center...
1958-82 Chevrolet; Lower Ball Joint with Hardware; Various Applications
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
1960-62 Chevy, GMC Pickup, Suburban; Disc Brake Drop Spindles; 2.5"; RH & LH; Pair
These reproduction 2.5 inch drop spindles are designed to lower your Chevrolet or GMC truck while maintaining factory style ride quality and proper suspension geometry. Manufactured to precise factory specifications, each...
1974-78 Ford Mustang II, Pinto; Spindle Set; Forged Steel; Stock Height; Pair
Our Mustang II stock height front spindles are built from forged steel and heat treated for superior strength. Will fit 1974-78 Ford Mustang, 1974-80 Ford Pinto, and 1975-80 Mercury Bobcat. Mustang II style spindles are also...
Grade 5, size 7/16-14 USS hex nut, in zinc plated finish. Sold individually. Specifications: Screw Size : 7/16-14 Across Flats : 11/16" Grade : 5 S.A.E. Standard : J995 Finish : Zinc Proof Load : 120000 Rockwell Hardness :...
1974-78 Mustang II; Front Sway Bar Kit; 3/4" ; 43-1/4" Wide; for Standard Crossmember
Replacement 3/4" sway bar kit for hot rods and custom trucks equipped with standard width crossmember Mustang II front suspension systems. This sway bar is engineered to reduce body roll, under steer, and over steer during...
1958-64 Impala / Full Size Upper Control Arm; LH
This is a reproduction of the upper left hand control arm used on 1958-64 full size models. Note: This is the control arm only, ball joints, bumpers, shafts and bushings are sold separately. For rig ht hand side use Part #...
1958-64 Impala, Bel Air, Biscayne; Lower Control Arm Shafts; Pair
Reproduction of the original style lower control arm shafts for 1958-1964 Impala, Bel Air, Biscayne, and other full size Chevrolet models. Each set is designed to restore proper suspension geometry while maintaining an...
1958-64 Impala, Bel Air, Biscayne; Upper Control Arm Shaft; Pair; LH & RH; Pair
Quality reproduction lower control arm cross-shafts for various 1958-1964 Chevrolet Impala, Bel Air, and Biscayne models. Each shaft is manufactured in high quality stamped steel and built to original factory specifications...
Front Boxing Plate set designed for use when boxing in the frame. These boxing plates weld into place to box the frame in critical front suspension attachment points when converting to a Mustang II style IFS - Independant...
1960-70 Chevy, GMC Truck; Upper Ball Joint with Hardware; RH or LH
Reproduction of the original upper ball joint and hardware designed to replace the old or worn out originals. If your suspension rattles or makes noises when turning or going over bumps, it might be time to think about...
1958-64 Impala; Bel Air; Biscayne; 1963-82 Corvette; Lower Control Arm Bumper
Replacing the control arm bumper can help bring the suspension back to factory original condition and keep it from bottoming out.
1960-63 Chevy Pickup 2 WD; 1963-74 Chevrolet Corvette; Strut Rod Bushing; 1.20"; Each
Reproduction strut rod bushing for 1963-74 Chevrolet Corvette models. This authentic replacement is manufactured using high quality automotive grade molded rubber and matches the original 1.20" diameter design for proper fit...
Sway Bar Bracket; Tab Style; Universal; End Link to Lower Control Arm or Frame Rail, LH or RH
This universal sway bar end link bracket is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
New reproduction of the OEM 1958-88 GM heavy duty front sway bar/stabilizer bar bushing WS6 for multiple GM vehicles including Chevrolet Chevelle, Buick Skylark, Oldsmobile Cutlass and Pontiac GTO models with 7/8" diameter...
New reproduction of the OEM 1958-88 GM heavy duty front sway bar/stabilizer bar bushing for multiple GM vehicles including Chevrolet Chevelle, Buick Skylark, Oldsmobile Cutlass and Pontiac GTO models with 1-1/8" diameter...
This universal sway bar end link bracket set is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
7/16"-20 Finished Nut; Grade 8; Domestic; Each
Nut 7/16"-20 Grade 8 Hi.625 Tall, 11/16 Hex Head. Hex nuts are six-sided, internally threaded fasteners, mated with bolts, studs, screws, and other externally threaded products. The addition of the hex nut ensures that the...
7/16" F436 Washer; Hardened; Heat-Treated; Domestic
7/16" F436 Washer. ASTM F436 covers the chemical and mechanical requirements for hardened washers in diameters ranging from 1/4" to 4" inclusive. These heat treated washers are for general purpose and structural use. For use...
1961-75 Buick, Chevy, Olds, Pontiac; Upper Control Arm Bumper; Each
Quality reproduction of the original upper control arm bumper designed for use with various 1967-75 General Motors models. Each bumper is manufactured in heavy duty EPDM molded rubber material to original specifications...
1959-70 Impala, Bel Air, Biscayne, Caprice; Trailing Arm Bushing; Each
Rear trailing arm bushing for various 1959-1970 GM full size models including Impala, Bel Air, Caprice, and Biscayne. This high quality reproduction bushing is engineered to replace the worn or deteriorated original,...
1955-74 Buick, Chevy, Olds, Pontiac; Upper Control Arm Bushing; Each; Various Models
1958-1970 Chevrolet Biscayne 1958-1970 Chevrolet Bel Air 1966-1970 Chevrolet Caprice 1970-1972 Chevrolet Monte Carlo 1968-1968 Chevrolet Chevy II 1968-1974 Chevrolet Nova 1955-1957 Chevrolet Bel Air 1955-1957 Chevrolet One...
1958-64 Impala, Bel Air, Biscayne; Tubular Control Arm Set; Black;
Tubular control arms are engineered for maximum strength, durability, and visual impact. Designed as direct stock replacements, these upper control arms provide a cleaner appearance and significantly increased rigidity over...
1959-64 Impala, Bel Air, Biscayne; Rear Lower Trailing Arm Bushing; Front of Arm; Each
Rear trailing arm rubber bushing for various 1959-1964 GM full size models including Impala, Bel Air, El Camino, Parkwood, Brookwood, and Biscayne. This high quality replacement bushing is designed to restore proper...
1959-64 Impala, Bel Air, Biscayne; Rear Control Arm Bolt Set; With Integrated Shock Mounting Studs
Reproduction of the often damaged or rusted rear control arm bolt set. Each set includes two of the special bolts, nuts, and lock washers that are required for mounting the lower eyelet of the shock absorbers to the rear...
1960-91 Chevrolet, GMC C/K Pickup, Suburban; Upper Control Arm Bumper; Each
Reproduction upper control arm bumper for 1960-72 Chevrolet and GMC 1/2 ton, 3/4 ton, and 1 ton truck models, and 1973-91 Chevrolet and GMC 3/4 ton and 1 ton truck models. Each bumper is manufactured in heavy duty EPDM molded...
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate
Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...
Emblem Installation Speed Nut Set ; 5/16" ; 8 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 8...
Emblem Installation Speed Nut Set ; 5/16"; 4 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 4...