Coil Spring Spacer; 9/16" Thick; EPDM Rubber; Each
Reproduction of the original 9/16" coil spring spacer designed for various GM models. This spacer is manufactured from durable EPDM rubber. This spacer was used to correct the ride height on vehicles that did not sit level...
1958-64 Impala, Bel Air, Biscayne; Front Tubular Lower Control Arms; Pair
These performance tubular lower control arms are designed to accept the standard coil spring, coil-over shocks or shocks with air bags. The arms are powder coated black and pre-assembled with our Del-a-lum bushings, billet...
1958-64 Impala, Bel Air, Biscayne; Front Tubular Upper Control Arms; Pair
Reproduction of the original upper tubular upper control arms designed for use with 1958-64 Impala, Bel Air, Biscayne, and Full Size Chevrolet models. These tubular style upper control arms change the way the car drives and...
Reproduction lower control arm bushings for 1955-64 Chevrolet Bel Air, Impala, Corvair, and Full Size models. Each bushing is manufactured to factory specifications. Add new life to your suspension by replacing the old...
1954-05 Front Sway Bar End Link; 3-3/8" Spacer; LH or RH Side; 2 Required
Includes all the components to replace the original bushings and hardware. Each set includes 4 bushings, 1 bolt, 1 nut, 4 washers, and 1 spacer. Set does only 1 side. 2 required per vehicle. {fitment}
1958-64 Impala / Full Size Upper Control Arm; RH
This is a reproduction of the right hand upper control arm used on 1958-64 full size models. For left hand side use Part # A1000. Note: This is the control arm only, ball joints, bumpers, shafts and bushings are sold...
Reproduction bushing for the rear panhard rod on 1959-64 Chevrolet Impala, Bel Air, Biscayne models, and for the rear strut rod on 1959-62 Corvette. If your full size Chevrolet or Corvette model is feeling loose around...
1958-64 Impala, Bel Air, Biscayne; Upper Control Arm Shaft Set
Reproduction of the original style upper control arm shafts for use with 1958-64 Impala, Bel Air, and Biscayne models. Set include shafts, bushings, washers and washer/bushing retainer bolts. {fitment}
1958-64 Impala, Bel Air, Biscayne; Lower Control Arm Shaft; LH or RH
Quality reproduction of the lower control arm cross-shaft for use on various 1958-64 Chevrolet Impala, Bel Air, Biscayne, and 1963-82 Corvette models. Each control arm shaft is manufactured in quality stamped steel to...
Reproduction molded rubber front coil spring insulator that mounts between the coil spring and the frame on various 1949-96 vehicles. This insulator keeps the spring from riding metal-to-metal on the frame. Coil spring...
1958-64 Impala, Bel Air, Biscayne; Upper Control Arms; Rubber Bushings; Pair
New stock style upper control arms designed for use with 1958-64 Chevrolet Impala, Bel Air, Biscayne, and full size models. Includes both RH and LH upper control arms with cross shafts, bushings, and ball joints...
1955-70 Full Size Chevy; Upper Ball Joint; with Hardware; RH or LH
Reproduction of the original upper ball joint designed for use with 1955-70 Chevy full size models including 1955-57 Chevy, and 1958-70 Impala, Bel Air, Biscayne, and Caprice models. Control arm ball joints take a beating...
1958-82 Chevrolet; Lower Ball Joint with Hardware; Various Applications
Control arm ball joints take a beating over the years and often cause "slop" in your front end, creating dangerous driving conditions. If your suspension rattles or makes noises when turning or going over bumps, it might be...
Grade 5, size 7/16-14 USS hex nut, in zinc plated finish. Sold individually. Specifications: Screw Size : 7/16-14 Across Flats : 11/16" Grade : 5 S.A.E. Standard : J995 Finish : Zinc Proof Load : 120000 Rockwell Hardness :...
1974-78 Ford Mustang II, Pinto; Spindle Set; Forged Steel; Stock Height; Pair
Our Mustang II stock height front spindles are built from forged steel and heat treated for superior strength. Will fit 1974-78 Ford Mustang, 1974-80 Ford Pinto, and 1975-80 Mercury Bobcat. Mustang II style spindles are also...
1958-64 Impala / Full Size Upper Control Arm; LH
This is a reproduction of the upper left hand control arm used on 1958-64 full size models. Note: This is the control arm only, ball joints, bumpers, shafts and bushings are sold separately. For rig ht hand side use Part #...
1974-78 Mustang II 3/4" Front Sway Bar; Measures 43-1/4" Wide; For Standard Crossmember
Replacement 3/4" sway bar kit for hot rods and custom trucks running standard width crossmember Mustang II front suspension. Designed to minimize body roll, under-steer and over-steer when cornering, resulting in improved...
1958-64 Impala; Bel Air; Biscayne; 1963-82 Corvette; Lower Control Arm Bumper
Replacing the control arm bumper can help bring the suspension back to factory original condition and keep it from bottoming out. {fitment}
7/16"-20 Finished Nut; Grade 8; Domestic; Each
Nut 7/16"-20 Grade 8 Hi.625 Tall, 11/16 Hex Head. Hex nuts are six-sided, internally threaded fasteners, mated with bolts, studs, screws, and other externally threaded products. The addition of the hex nut ensures that the...
7/16" F436 Washer; Hardened; Heat-Treated; Domestic
7/16" F436 Washer. ASTM F436 covers the chemical and mechanical requirements for hardened washers in diameters ranging from 1/4? to 4? inclusive. These heat treated washers are for general purpose and structural use. For use...
1961-75 Buick, Chevy, Olds, Pontiac; Upper Control Arm Bumper; Each
Quality reproduction of the original upper control arm bumper designed for use with various 1967-75 General Motors models. Each bumper is manufactured in heavy duty EPDM molded rubber material to original specifications...
1959-70 Chevrolet Impala/Full Size; Trailing Arm Bushing; Each
Rear trailing arm bushing for various 1959-70 GM Full size models including Impala, Bel Air, Caprice and Biscayne. This reproduction bushing is designed to replace the old or worn out original. Manufactured from hard rubber...
1958-64 Tubular Control Arm Set - Black
Tubular control arms are designed for maximum strength and visual impact. These upper arms are designed for stock replacement. All arms capture both sides of the bushing, unlike the originals that were only retained on one...
1959-64 Chevrolet Impala/Full Size; Bushing; Rear; Lower Trailing Arm; Front of Arm; Each
Rear trailing arm rubber bushing for various 1959-64 GM Full size models including Impala, Bel Air, El Camino, Parkwood, Brookwood and Biscayne. This bushing will replace the old or worn out original. Sold individually....
1959-64 Impala, Bel Air, Biscayne; Rear Control Arm Bolt Set; With Integrated Shock Mounting Studs
Reproduction of the often damaged or rusted rear control arm bolt set. Each set includes two of the special bolts, nuts, and lock washers that are required for mounting the lower eyelet of the shock absorbers to the rear...
Spindle Nut & Cotter Pin; 3/4"-20 With 1-1/16" Hex Head
3/4"-20 With 1-1/16" hex head spindle nut and plated 1/8" x 1-1/2" cotter pin for securing drum or rotor to spindle. Kit contains one nut and one cotter pin. 2 kits required per vehicle. {fitment}
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate
Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...
Emblem Installation Speed Nut Set ; 5/16" ; 8 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 8...
Emblem Installation Speed Nut Set ; 5/16"; 4 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 4...