Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 AMC, GM, Ford, Mopar; Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
1947-72 Chevrolet/GMC Truck Outer Door Mirror Arm Mounting Screw Set
OER® reproduction 3 piece stainless steel screw set for mounting the outer door side mirror arms on 1947-72 Chevrolet and GMC trucks. One set per mirror arm required. Note: Not for use on 1970-72 door mirror assemblies....
1960-63 Chevy, GMC Pickup, Suburban; Windshield Glass; Gray Tinted Without Shade
Reproduction curved front windshield glass for 1960-63 Chevrolet and GMC pickup, and Suburban models as listed. Windshields are manufactured using tempered laminate safety glass designed for protection against road debris....
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
1960-66 Chevy, GMC Pickup, Panel, Suburban; Door Check Assembly; LH or RH; Each
OER® Authorized reproduction door check for 1960-66 Chevrolet & GMC model trucks. Designed to prevent the door from opening too far, this reproduction is precision manufactured for an exact replacement of the original...
1960-63 Chevy, GMC Pickup, Suburban; Windshield Glass; Gray Tinted With Dark Gray Shade
Reproduction curved front windshield glass for 1960-63 Chevrolet and GMC pickup, and Suburban models as listed. Windshields are manufactured using tempered laminate safety glass designed for protection against road debris....
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
1960-66 Chevy, GMC Truck; Windshield Wiper Blade; with Red Dot Push Button; 13" Long; Each
Reproduction "Red Dot" style 13" windshield wiper blades for 1960-66 Chevrolet and GMC truck and a variety of other models. Each blade features polished stainless steel construction and accepts a 3/16" narrow-style bayonet...
1960-66 Chevrolet, GMC Pickup; Stepside; Chrome Rear Bumper; Show Quality
OER Premier® reproduction of the original chrome rear bumper designed for use with 1960-66 Chevrolet and GMC Stepside Pickup truck models. Each bumper is manufactured to OE specifications replicating the original in...
1947-72 Chevrolet/GMC Truck; Round Door Mirror Head; Chrome; Smooth Backing
Reproduction exterior round mirror head for 1947-72 Chevrolet & GMC truck models. This reproduction mirror head is design to replace the worn out or missing original. Features a chrome backing with a 5" smooth, non-ribbed...
1960-63 Chevy, GMC Pickup, Suburban; Windshield Glass; Tinted
Reproduction curved front windshield glass for 1960-63 Chevrolet and GMC pickup, and Suburban models as listed. Windshields are manufactured using tempered laminate safety glass designed for protection against road debris....
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
1960-66 Chevy, GMC Pickup, Panel, Suburban; Hood Hinge Springs; Polished Stainless; RH & LH: pair
Take your restoration to the next level with these custom polished stainless steel hood hinge springs for 1960-66 GM truck models. Precision-engineered to fit and function like the originals, these springs not only deliver...
1960-72 Chevrolet, GMC Truck; Door Latch Screw Set; 12 Piece Set; 6 Screws, 6 Washers
OER® Authorized reproduction door latch screws and lock washers for 1960-72 Chevrolet and GMC truck models. Screws are 5/16"-18 thread, measure 3/4" in thread length and 1 inch in overall length. Set of 6 screws and 6...
1960-66 Chevrolet/GMC Truck. Suburban; Outer Door Handle Set; With Gaskets And Hardware
OER® Authorized reproduction outer door handle and push button set for 1960-66 Chevrolet and GMC pickup truck models. These outer door handles are manufactured in quality die-cast zinc featuring a beautifully chromed...
1954-87 Chevy, GMC Stepside; Rear Roll Pan; with License Plate Pocket; without License Lamps
Customize the rear end of your classic Chevrolet or GMC stepside pickup truck with a sleek looking steel rear roll pan. This all steel roll pan is just what you need to add a cutom appearance. Manufactured in stamped steel...
Replacement style stainless steel capped bumper bolt and nut designed for use on many GM vehicles. Each bolt measures 1/2"-13 x 1-1/2"; 1-1/8" head diameter and comes complete with attaching nut. Can be used for a wide...
Ford, GM, Mopar; Windshield Wiper Blade Refill; 16"; Pair
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
1960-66 Chevrolet, GMC Pickup, Suburban; Windshield Wiper Motor Transmission Arm Set
Reproduction windshield wiper motor transmission arm assembly for 1960-66 Chevrolet and GMC pickup and Suburban models. Each set is manufactured in hardened steel to correct factory dimensions. Will completely replace the...
1954-87 Chevrolet/GMC Truck; Tail Gate Trunnions; Stepside
Reproduction lower trunnions designed for 1954-1987 Chevrolet and GMC stepside pickup truck models. Each trunnion is manufactured to original factory specifications and plated for long lasting dependability. The trunnions...
1960-66 Chevy, GMC Pickup, Suburban; Hood Hinge Assembly; EDP Coated; RH Passenger Side
Reproduction hood hinge assembly for 1960-66 Chevrolet and GMC pickup truck, panel truck, and Suburban models. Each hood hinge is manufactured in quality stamped steel, replicating the original in design, appearance, and...
1960-66 Chevrolet, GMC Pickup; Back Window Glass; Tinted; Large 14" x 60"
Reproduction of the original large format back window glass designed for use with 1960-66 Chevrolet and GMC pickup models. Each glass is manufactured to factory specifications replicating the original in design, appearance,...
1960-62 Chevy, GMC Fleetside Truck; Rear Bumper Bracket Set; with Hardware
Reproduction rear bumper brackets for 1960-62 Chevrolet and GMC Fleetside models. Each bracket is manufactured from quality stamped steel to the correct configuration with pre-punched holes for straightforward installation....
1960-84 Windshield Wiper Blade; 16" Trico; Rainbow Type; 1/4" Bayonet Connector; Matt Stainless
Reproduction of the original Trico Rainbow Type wiper blade designed for various models originally equipped with Trico blades. Each wiper blade will replace the original and offer years of service. Each blade comes complete...
1960-66 Chevrolet, GMC Pickup; Back Window Glass; Large; Clear; 14" x 60"
Reproduction back window glass for 1960-66 Chevrolet and GMC pickup models. This back window glass measures approximately 14" x 60". This glass window is manufactured to original factory dimensions for a factory original...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
1955-72 Chevrolet, GMC Pickup Long Bed; Bed Mounting Pad Set; 1/2 Ton; 10 Piece Set
Keep the truck bed in proper alignment by replacing the old or worn out mounting pads. This mounting pad set is designed for use with 1947-72 Chevrolet and GMC 1/2 ton pickup trucks with long bed. Each set contains the...
1960-63 Chevy, GMC Pickup, Panel, Suburban; Door Latch Assembly; LH Driver Side
OER® Authorized reproduction door latch assembly designed for use with 1960-63 Chevrolet and GMC Pickup, Panel Truck, and Suburban models. Each latch is precision manufactured from quality stamped steel and accurately...
1967-69 Camaro, Firebird; Convertible Top Boot Interior Snaps; with Screws; 4 Piece Set
Reproduction convertible top boot snap and screw set for 1967-69 Camaro and Firebird models and any other vehicle that requires a screw-on style snap. These snaps are used to secure the convertible top to the inner rear...
1960-66 Chevrolet, GMC, Pickup, Panel, Suburban; Hood Hinge Spring; Each
Restore smooth hood operation with this high-quality reproduction hood hinge spring for 1960-66 Chevrolet and GMC trucks. Built to precise factory specifications, this spring ensures correct fitment, authentic tension, and...
1960-63 Chevy, GMC Pickup Truck, Suburban; Manual Door Window Regulator; LH Driver Side
Reproduction manual window regulator for 1960-63 Chevrolet, GMC pickup and Suburban models. Each regulator is manufactured in quality stamped steel to correct factory specifications replicating the original design, fitment,...
1960-63 Chevy, GMC Pickup, Panel, Suburban; Door Latch Assembly; RH Passenger Side
OER® Authorized reproduction door latch assembly designed for use with 1960-63 Chevrolet and GMC Pickup, Panel Truck, and Suburban models. Each latch is precision manufactured from quality stamped steel and accurately...
Tapping Screw; #8 x 1"; Phillips Pan Head; A/AB; Black Oxide
This reproduction screw can be used on many applications where a #8 X 1" phillips pan head Black Oxide plated tapping screw is needed. Sold individually.
Reproduction zinc-plated bumper bolt with a polished stainless steel capped head for a variety of GM, Ford and Mercury applications including 1958-66 Chevrolet, 1965-68 Ford Mustang, 1960-67 Ford Falcon and 1960-65 Mercury...
1958-66 Chevrolet/GMC Truck; Tail Gate Trunnions; With Brackets; Fleetside
Reproduction lower trunnions for 1954-1966 Chevrolet and GMC Fleetside pickup truck models. Each trunion is manufactured to original factory specifications featuring a cadmium plating for long lasting dependability. The...
Reproduction 16" windshield wiper blade for a variety of GM vehicles that require a 16" side lock blade. Each blade is manufactured in stainless steel and finished in satin silver as original. Fits the side lock style...
1960-66 Chevy, GMC Pickup; Back Window Glass; Tinted; Small 10" x 38"
Reproduction of the original small format tinted back window glass designed for use with 1960-66 Chevrolet and GMC pickup models. Each glass is manufactured to factory specifications replicating the original in design,...
1960-66 GM Pickup with Small 10" x 38" Window Smoke Back Window Glass
Replace scratched, damaged or missing original glass with our OER® Authorized quality replacement. Each glass is professionally packed with extra care to avoid damage during shipping. The OER® Authorized logo...
Spring Steel Rod Clip, for Carburetor, Door, Tailgate; LH Driver Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...
1960-66 Chevy, GMC Pickup, Panel, Suburban; Lower Rear Fender Mounting Bracket; RH Passenger Side
Restore proper support and alignment with these reproduction lower front fender mounting plates and reinforcement braces designed for 1960-66 Chevrolet and GMC truck models. Each plate is precision-stamped from quality steel...
1960-66 Chevy, GMC Pickup, Panel, Suburban; Lower Rear Fender Mounting Bracket; LH Driver Side
Reinforce your front end with these reproduction lower front fender mounting plates and reinforcement braces designed for 1960-66 Chevrolet and GMC truck models. Each component is precision-stamped from quality steel to...
1958-66 Chevrolet, GMC Fleetside Pickup; Tailgate Chain Set; With Hardware; Chrome-Plated
Tailgate chain assemblies are used on Fleetside trucks as a method of supporting the gate when open, and securing the gate when it is closed. Each set is manufactured in steel, chrome-plated for corrosion resistance and a...
1964-98 GM; Door Lock Striker Bolt Washer Shim ; 1.25MM Thick ; Each; Various Models
Reproduction of the original door striker bolt shim manufactured in die-stamped steel and finished in clear zinc coating. Used to correctly position the door striker bolt for proper alignment with the door latch assembly. Use...
Secure your rear fenders with this replacement-style Phillips head bolt and hardware set designed for 1947-66 Chevrolet and GMC Stepside models. This kit provides a functional solution for attaching both left-hand and...
1958-66 Chevrolet, GMC Fleetside Pickup; Tailgate Chain Set; With Hardware; Zinc-Plated
Tailgate chain assemblies are used on Fleetside trucks as a method of supporting the gate when open, and securing the gate when it is closed. Each set is manufactured in steel, zinc-plated for corrosion resistance, and...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
Hex Washer Head Spin Lock Bolt; 5/16" X 18 X 1-1/4"; Phospate Coating" Each
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished iin a black phospate coating for an authentic original appearance and corrosion resistance. Sold individually. Use as required. Product Specifications:...
Bumper Bolt; Stainless Steel Cap; Flat Head; 3/8"-16X 15/16"; Package of 25
Package of 25 reproduction bumper bolts that measure 7/16-14 x 1-1/2" with a stainless steel cap and round head. Willl fit a wide variety of vehicles including 1957-72 Ford F-Series Truck and many other Ford Motor Company...
1960-66 Chevy, GMC Pickup, Panel, Suburban; Front Bumper Bracket & Hardware Set; 6 Piece Set
Restore the original structure and alignment of your classic GM truck's front end with this high-quality reproduction front bumper bracket set, designed for use on 1960-1966 Chevrolet and GMC truck models. Each bracket is...
1954-87 Chevrolet GMC Stepside Pickup; Tailgate Chains; Zinc Plated
Reproduction tailgate chain assemblies for 1954-87 Chevrolet and GMC Stepside pickup trucks. These tailgate chains feature zinc plated coating offering authenticity an original appearance. These chains are used as a method of...
1960-63 Chevrolet, GMC Pickup Truck; Door Vent Window Glass; Clear; 6" x 16"; RH or LH; Each
Reproduction of the original door vent glass designed for use with 1960-63 Chevrolet and GMC pickup truck models. Each glass is manufactured to OE specifications offering an authentic appearance and fit. The glass features a...
1960-63 Chevrolet, GMC Pickup Truck; Door Vent Window Glass; Green Tinted; 6" x 16"; RH or LH; Each
Reproduction of the original door vent glass designed for use with 1960-63 Chevrolet and GMC pickup truck models. Each glass is manufactured to OE specifications offering an authentic appearance and fit. The glass features a...
Reproduction of the original Trico Style wiper blade refill designed for use on the various models that require a 16" Trico style rainbow type wiper blade. Each wiper blade assembly will replace the original and offer years...
#10-24 x 1"; Phillips Oval Head Head Machine Screw; Stainless Steel
Stainless Steel Phillips #10-24 x 1" Oval Head Head Machine Screw. Sold individually. Specifications: Thread Diameter : 10-24 Length : 1" Head Style : Phillips Oval Head Size : Std Material : 18-8 Stainless Steel
Plastic Retainer; Push-In Type Rivet; 7/8" Head Diameter; 1-3/64" Stem Length; For 1/2" Hole
Reproduction push-in retainer designed to attach the front urethane bumper cover to the impact bar. Push-in style. 28.2mm long. Manufactured in durable ABS black plastic material. Sold individually. Use as required. Replaces...