1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
1959-60 Impala, Bel Air, Biscayne; NiTerne Coated Fuel Tank; with Neck; 16 Gallon
Reproduction of the original fuel tank designed for use with 1959-60 Chevrolet Impala, Bel Air, and Biscayne models (except El Camino, station wagon). This reproduction fuel tank is manufactured in quality stamped steel...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1959-60 Impala, Bel Air, Biscayne; Zinc Coated Fuel Tank; with Neck; 16 Gallon
Reproduction of the original fuel tank designed for use with 1959-60 Chevrolet Impala, Bel Air, and Biscayne models (except El Camino, sedan delivery, or station wagon). This reproduction fuel tank is manufactured in quality...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
Reproduction of the original gas tank straps designed for use with 1959-1960 Chevrolet Bel Air, Impala, and Biscayne models. Each strap is manufactured in quality stainless steel with all correct contours for an authentic...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
1955-70 Impala, Full Size; Fuel Tank Mounting Strap Hardware Set; 6-Pieces
Use proper mounting hardware to make your fuel tank installation job easier. This hardware set is the correct replacement fuel tank strap bolt set for 1955-70 full size Chevrolet models including 150, 210, Bel Air, Impala,...
1947-76 GM, Chrysler, Dodge, Plymouth; Brass Fuel Tank Sending Unit Float
Reproduction brass fuel sending unit float for various 1947-76 General Motors, and Chrysler, Dodge, Plymouth models. If your fuel gauge isn't reading correctly, it may be the fuel sending unit float. The original OE float may...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
1958-60 Impala, Bel Air, Biscayne; Fuel Tank Sending Unit; with 348 ci; 3/8" Inlet
Reproduction fuel tank sending unit for 1958-60 Chevrolet Impala and Full Size models with 348ci engines. Features the original design for an authentic fit and genuine appearance. Each sending unit includes the sender,...
1958-60 Impala, Bel Air, Biscayne; Fuel Tank Sending Unit; 5/16" Inlet; 6 or 8 Cyl.; Except 348 ci
Reproduction fuel tank sending unit for various 1958-60 Chevrolet Impala and Full Size hardtop and sedan models. Features the original design for an authentic fit and genuine appearance. Each sending unit includes the sender,...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 100 GPH - 7 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 140 GPH - 9 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...