1955-57 Chevy Bel Air, 150. 210; Upper Control Arms; Rubber Bushings; Pair
New stock style upper control arms for 1955-57 Chevrolet Bel Air, 150, 210, and Nomad models. Includes a pair with cross shafts, bushings, and ball joints installed. These are made from heavy gauge steel and black...
Leaf Spring U-Bolts; 3-1/4" Wide X 6-3/4" Long; Fits 3-1/4" Axle Tubes
Replacement OE-style U-bolts and nuts for rear leaf springs from OER®. 2 pair required per axle. Comes with heat treated grade 8 nuts and F436 heat treated and hardened heavy duty washers. {specs} Applications: 1973-74...
Coil Spring Spacer; 9/16" Thick; EPDM Rubber; Each
Reproduction of the original 9/16" coil spring spacer designed for various GM models. This spacer is manufactured from durable EPDM rubber. This spacer was used to correct the ride height on vehicles that did not sit level...
1955-57 Chevrolet Bel Air, 150, 210; 2" Drop Spindles; RH and LH; Pair
These one piece spindles allow you to lower vehicle ride height 2" without affecting steering geometry or suspension travel, which also eliminates the need for bolt-on caliper brackets or steering arms. Cast from the highest...
1955-57 Chevy Bel Air, 150, 210; Lower Tubular Control Arms; Pair
Tubular control arms are designed for maximum strength and visual impact. These control arms are designed for a stock replacement offering a great look. All arms capture both sides of the bushing, unlike the originals that...
1955-57 Chevrolet 150/210/Bel Air; Front Suspension Rebuild Set; Manual Steering
Despite it's durability (when new), the front suspension of your classic Chevrolet is still prone to wear out with age. Restore handling and reduce front tire wear with this rebuild set. This set will renew your worn out...
Reproduction lower control arm bushings for 1955-64 Chevrolet Bel Air, Impala, Corvair, and Full Size models. Each bushing is manufactured to factory specifications. Add new life to your suspension by replacing the old...
Rear sway bar for 1955-57 Chevrolet Bel Air, One-Fifty series, Two Ten series (except Nomad or wagon models). This sway bar is designed to minimize body roll, under-steer and over-steer when cornering, resulting in improved...
Mustang II Top Spring Hat Set; For Weld-In Mustang II Front Suspension Conversion
Universal weld-in Mustang II upper crossmember spring hat set designed to be used when converting your vehicle to Mustang II style front suspension. Produced in heavy duty steel, tig-welded, and ready for you to weld into...
1955-57 Chevy Bel Air, 150, 210; Upper Control Arm Shaft Set; with Rubber Bushings
This reproduction upper control arm shaft set is for use on 1955-57 full size models. These upper shafts have an extra 2 degrees of caster built into them. The added caster is a must for cars equipped with power steering....
1956-57 Chevy Bel Air, 150, 210; Leaf Spring Shackle Set; LH Driver Side
Reproduction rear leaf spring shackle for 1956-57 Chevrolet Bel Air, 150, 210 models. This shackle set is manufactured to correct factory specifications offering an authentic replacement to the old or worn out original...
Includes all the components to replace the original bushings and hardware. Each set includes 4 bushings, 1 bolt, 1 nut, 4 washers, and 1 spacer. Set does only 1 side. 2 required per vehicle. Has 2" Spacer {fitment}
Reproduction molded rubber front coil spring insulator that mounts between the coil spring and the frame on various 1949-96 vehicles. This insulator keeps the spring from riding metal-to-metal on the frame. Coil spring...
1955-57 Chevrolet Passenger Car Tubular Control Arm Set Upper and Lower
These tubular control arms are designed for maximum strength and enhance the handling performance of 1955-57 Chevrolet passenger car models. These arms are not only stronger and lighter weight than the factory arm, they also...
1955-57 Chevy Bel Air, 150, 210; Upper Tubular Control Arms; Pair
Enhance the handling performance of your 1955-57 Chevrolet Bel air, 150, 210, or Nomad model with tubular control arms. These arms are not only stronger and lighter weight than the factory arm, they also feature improved...
1955-57; Chevrolet Bel Air, 150, 210; Front End Rebuild Set; Basic; Manual Steering
Reproduction of the original components required to rebuild the front end for 1955-57 Chevrolet Bel Air, 150, 210 models. Each componet is manufactured to original factory specifications in the OE rubber material replicating...
1955-70 Full Size Chevy; Upper Ball Joint; with Hardware; RH or LH
Reproduction of the original upper ball joint designed for use with 1955-70 Chevy full size models including 1955-57 Chevy, and 1958-70 Impala, Bel Air, Biscayne, and Caprice models. Control arm ball joints take a beating...
1955-57 Chevrolet Bel Air, 150, 210; Econo Line Disc Brake Drop Spindles; 2" Drop
This 2" drop spindle set for 1955-57 Chevrolet Bel Air, One-Fifty or Two-Ten models is compatible with most aftermarket single-piston disc brake kits. Spindles use stock steering arms and will improve steering and handling,...
Grade 5, size 7/16-14 USS hex nut, in zinc plated finish. Sold individually. Specifications: Screw Size : 7/16-14 Across Flats : 11/16" Grade : 5 S.A.E. Standard : J995 Finish : Zinc Proof Load : 120000 Rockwell Hardness :...
1974-78 Ford Mustang II, Pinto; Spindle Set; Forged Steel; Stock Height; Pair
Our Mustang II stock height front spindles are built from forged steel and heat treated for superior strength. Will fit 1974-78 Ford Mustang, 1974-80 Ford Pinto, and 1975-80 Mercury Bobcat. Mustang II style spindles are also...
1974-78 Mustang II 3/4" Front Sway Bar; Measures 43-1/4" Wide; For Standard Crossmember
Replacement 3/4" sway bar kit for hot rods and custom trucks running standard width crossmember Mustang II front suspension. Designed to minimize body roll, under-steer and over-steer when cornering, resulting in improved...
1955-57 Bel Air, 150, 210; Lower Control Arm Rubber Bumper; Each; OER
Reproduction of the original front lower control arm bumper designed for use on all 1955-57 Chevrolet car models. This control arm bumber is manufactured in hard rubber with the correct threaded mounting stud as original....
1955-57 Chevy Bel Air, 150, 210; Lower Control Arm Shaft Set; with Rubber Bushings
Reproduction of the original lower control arm shaft for use on 1955-57 Chevrolet Bel Air, 150, 210, and Nomad models. These lower shafts include rubber bushings, washers and washer/bushing retainer bolts. {fitment}
1955-57 Chevy Bel Air, 150, 210; Lower Control Arm Ball Joint
Reproduction of the original lower control arm ball joint designed for use with 1955-57 Chevrolet Bel Air, one-Fifty Series, Two-Ten Series, and Nomad models. Control arm ball joints take a beating over the years and often...
1956-57 Chevrolet Bel Air; Leaf Spring Shackle Set; RH Passenger Side
Reproduction rear leaf spring shackle set for 1956-57 Chevrolet Bel Air and Full size models. Your leaf spring shackles are usually in poor shape when removed, don't reinstall worn out parts. For use on the RH passenger side....
1955-57 Chevrolet Bel Air, 150, 210; Front Spring Bolt & Nut Set
This is the bolt and nut that secures the front of the leaf spring into the spring pocket. Set includes one bolt and one nut. Two sets required per car. {fitment}
Front Boxing Plate set designed for use when boxing in the frame. These boxing plates weld into place to box the frame in critical front suspension attachment points when converting to a Mustang II style IFS - Independant...
Sway Bar Bracket; Tab Style; Universal; End Link to Lower Control Arm or Frame Rail, LH or RH
This universal sway bar end link bracket is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
Sway Bar Bracket Set; Tab Style; Universal; End Link to Lower Control Arm or Frame Rail, LH and RH
This universal sway bar end link bracket set is for cars and trucks that did not come from the factory with a sway bar end link mount on the lower control arm or frame rail. Provides a solid mount to be used to secure the end...
7/16"-20 Finished Nut; Grade 8; Domestic; Each
Nut 7/16"-20 Grade 8 Hi.625 Tall, 11/16 Hex Head. Hex nuts are six-sided, internally threaded fasteners, mated with bolts, studs, screws, and other externally threaded products. The addition of the hex nut ensures that the...
7/16" F436 Washer; Hardened; Heat-Treated; Domestic
7/16" F436 Washer. ASTM F436 covers the chemical and mechanical requirements for hardened washers in diameters ranging from 1/4? to 4? inclusive. These heat treated washers are for general purpose and structural use. For use...
1955-72 GM; Lower Control Arm Bumpers; Polyurethane; Black; Pair
Polyurethane lower control arm bumper stops are guaranteed to last longer and perform better than O.E.M. rubber stops. Cushions impact between suspension components preventing excessive damage. Sold as a pair. 1 pair required...
1955-74 Buick, Chevy, Olds, Pontiac; Upper Control Arm Bushing; Each; Various Models
1958-1970 Chevrolet Biscayne 1958-1970 Chevrolet Bel Air 1966-1970 Chevrolet Caprice 1970-1972 Chevrolet Monte Carlo 1968-1968 Chevrolet Chevy II 1968-1974 Chevrolet Nova 1955-1957 Chevrolet Bel Air 1955-1957 Chevrolet One...
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate
Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...
Emblem Installation Speed Nut Set ; 5/16" ; 8 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 8...
Emblem Installation Speed Nut Set ; 5/16"; 4 Piece Set
Speed nuts for various original or reproduction emblems that include 5/16" mounting studs. This speed nut set can be utilized for many of the emblems and side marker bezels that don't include attaching nuts. Set includes 4...
1955-57 Chevrolet Rear Axle Bumper, Each
Reproduction of the original rear axle bumper designed for use on 1955-57 Chevrolet car models. Manufactured from molded rubber to factory specifications for originality. Mounts on the axle housing. Sold individually. 2...