1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models
OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long
This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...
Correct reproduction of the original fuel tank designed for with 1957 Chevrolet Bel Air, 150, and 210 models (except station wagon, Nomad models.. This reproduction fuel tank is manufactured in stainless steel replicating the...
Accelerator Throttle Rod; Universal Fit
Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...
1957 Chevy Bel Air, 150, 210; Niterne Coated Fuel Tank; 16 Gallon; w/Square Corners; with Vent Tube
Reproduction of the original fuel tank designed for use with 1957 Chevy Bel Air, 150, and 210 models (except wagon). This reproduction tank is manufactured in quality NiTerne coated steel and features square corners and comes...
Reproduction of the original Ni-Terne fuel tank designed for use exclusively with 1957 Chevrolet Bel Air, 150, 210 models except Nomad, and station wagons. This OE-quality Ni-Terne coated reproduction stamped steel fuel tank...
Reproduction of the original fuel tank designed for use with 1957 Chevy Bel Air, 150, and 210 models (except wagon). This reproduction tank is manufactured in quality zinc coated steel and features square corners and comes...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps
Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...
Reproduction fuel tank sending unit with original design for an authentic fit and genuine appearance. Each sending unit includes the sender, gasket, filter, and a brass float as original. This unit monitors the fuel level in...
A reproduction of the original upper fuel tank filler neck designed for use with 1957 Chevrolet Bel Air, 150, 210, and Del Ray, 2 & 4 door convertible, hardtop, and sedan models. Each filler neck is manufactured in quality...
1955-57 Chevy Bel Air, Corvette, 150, 210, Nomad; Accelerator Pedal Pad
Correct reproduction accelerator pedal for 1955-57 Chevrolet Bel Air, 150, 210, and Nomad models. Each pad is manufactured to correct factory specifications replicating the original in design and fitment. Features correct...
1957 Chevy Bel Air, 150, 210; Fuel Door Inner Support Box ; Inside Quarter Panel
Reproduction fuel box door for 1957 Chevrolet models. This reproduction is installed in the quarter panel where the gas fuel door is located. Manufactured in stamped steel to original specifications. Includes the fuel door...
Reproduction of the original gas tank straps designed for use with 1955-57 Chevrolet Bel Air, 150, 210, Del Ray coupe and sedan models. Each strap is manufactured in quality stainless steel with all correct contours for an...
1955-57 Chevrolet Wagon & Nomad; Fuel Tank Sending Unit; 3/8" Line
Reproduction fuel sender for your classic Chevy wagon or Nomad. Each sender is produced in quality steel to resist corrosion within your fuel tank. Provides the fuel gauge with the signal to indicate fuel level. Comes with...
1955-57 Chevrolet; Fuel Tank Sending Unit; For 9 Passenger Wagon; 5/16" Line
Reproduction fuel sender for your classic Chevy 9-passenger wagon. Each sender is produced in quality steel to resist corrosion within your fuel tank. Provides the fuel gauge with the signal to indicate fuel level. Comes with...
Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...
1946-02 GM; Various Models; Throttle Cable; 36""; Stainless Steel ; Cut-To-Fit
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black
This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...
1955-57 Chevrolet Station Wagon - Fuel Tank Support Straps - Steel (Pair)
Reproduction fuel tank mounting straps for 1955-57 wagon models. Produced using heavy duty zinc-plated material with all correct contours for an authentic fit and appearance.Approximate strap measurement bend to bend is - 32...
1956-62 GM; Fuel Tank Filler Hose; 2" ID x 4-7/16" Length
Reproduction fuel tank filler hose for 1957 models. Hose is specifically engineered to stand up to gasoline, fuel oil, and other petroleum-based products. Clamps sold seperately. Measures 4-7/16" in length, inside diameter...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length
Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...
Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length
Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....
Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.
Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...
1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"
Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...
Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps
Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...
Correct reproduction of the original fuel tank designed for with 1957 Chevrolet Bel Air, 150, and 210 models (except station wagon, Nomad models. This reproduction fuel tank is manufactured in stainless steel replicating the...
Reproduction clips used to mount the fuel line to the frame. Includes six 3/8" clips. Applications: 1967-69 Chevrolet Camaro - Big Block 1967-69 Chevrolet Camaro - Small Block w/4bbl 1965-86 Chevrolet/GMC Truck 1965-70...
Reproduction of the original fuel tank designed for use with 1957 Chevy Bel Air, 150, and 210 models (except wagon). This reproduction tank is manufactured in quality zinc coated steel and features square corners without a...
1955-70 Impala, Full Size; Fuel Tank Mounting Strap Hardware Set; 6-Pieces
Use proper mounting hardware to make your fuel tank installation job easier. This hardware set is the correct replacement fuel tank strap bolt set for 1955-70 full size Chevrolet models including 150, 210, Bel Air, Impala,...
1947-76 GM, Chrysler, Dodge, Plymouth; Brass Fuel Tank Sending Unit Float
Reproduction brass fuel sending unit float for various 1947-76 General Motors, and Chrysler, Dodge, Plymouth models. If your fuel gauge isn't reading correctly, it may be the fuel sending unit float. The original OE float may...
Reproduction of the original fuel tank sending unit designed for use with 1955-57 Chevrolet Bel Air, 150, 210 sedan and convertible models. Don't run out of fuel because of a defective sending unit. Replace that old worn out...
Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap
Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...
1955-57 Chevrolet Bel Air, 150, 210, Nomad; Fuel Sending Unit & Filler Neck O-Ring
Reproduction of the original style fuel sending unit and filler neck O-ring designed for use with 1955-1957 Chevrolet Bel Air, 150, 210, and Nomad models. This O-ring is manufactured to correct factory dimensions and replaces...
A reproduction of the original upper fuel tank filler neck designed for use with 1957 Chevrolet Bel Air, 150, 210, and Del Ray, 2 & 4 door convertible, hardtop, and sedan models. Each filler neck is manufactured in quality...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 100 GPH - 7 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
Electric Fuel Pump; with Yellow Zinc Plated Housing; 140 GPH - 9 PSI
This externally-mounted electric fuel pump is ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT...
1955-57 Chevy Bel Air, 150, 210; Station Wagon; Fuel Tank Support Straps; Stainless Steel
Reproduction fuel tank mounting straps for 1955-57 Chevrolet Bel Air station wagon models. Produced using stainless steel material with all correct contours for an authentic fit and appearance. Approximate strap measurement...
1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit
Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...
Reproduction of the original fuel tank mounting straps designed for use with 1955-57 Chevrolet Bel Air, 150, 210, Del Ray coupe and sedan models. Each strap is manufactured in quality stamped steel, galvanized and EDP coated...
Fuel Tank Sending Unit; 5 Hole; Early Ford, AMC, and Mopar; 73-10 Ohm
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Fuel Tank Sending Unit; 5 Hole; "Universal" 240-33 Ohm; For Many Aftermarket Gauges
Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...
Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors
Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...
Hex Washer Head Bolt; Type F Thread Cutting; 3/8-16" x 1 3/4"; Each
Reproduction zinc chromate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 3/8-16" x 1 3/4"...
1955-69 GM; Accelerator Pedal Firewall Bushings; 1/2" Long, 5/16" I.D.; Pair
Reproduction accelerator firewall bushings for various 1955-69 GM models. These bushings are required to install the accelerator rod support correctly. They help to eliminate excessive play in the gas pedal pad while...
1947-66 Chevrolet/GMC Truck; 1955-57 Bel Air, 150, 210; Fuel Tank Sending Unit Screw Set
Reproduction of the original fuel tank sending unit screws and washers designed for use with 1947-66 Chevrolet, GMC trucks, and 1955-57 Bel Air, 150, 210, and Nomad models as listed. Each set features 5 phillips head screws...
Fuel Sending Unit Filter Strainer; For 5/16" Pickup Tube
Correct OER® reproduction of the original fuel tank float strainer designed for use with various 1942-85 GM, Chrysler, Dodge, Plymouth models as listed below. This filter will keep dirt and other elements from clogging or...
Reproduction of the original fuel tank sending unit designed for use with 1955-57 Chevy Bel Air, 150, 210, Nomad, and 1931-62 Chevy and GMC pickup truck models. Correct replacement of the original fuel tank sending unit...
1967-72 GM; Brake or Return Fuel Line Clip; Under Body; R-Profile; 3/16"; Each
Reproduction of the original under body brake and fuel line clip for various 1967-72 GM models. This clip secures the brake and fuel line to the under body to keep the brake and fuel lines out of harm's way. This is a 3/16"...
1955-57 Chevy Bel Air, 150, 210; License Lamp Wire Grommet & Sending Unit Wire Grommet; Each
Reproduction of the original style license lamp and sending unit wire grommet designed for use with 1955-57 Chevrolet Bel Air, 150, 210, and Nomad models as listed. Each grommet is manufactured in quality EPDM rubber...
Hex Head Sems Screw; With Washer; A/AB Point; 6.3-1.81 x 25mm; Black Phosphate; Each
Reproduction black phosphate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 6.3-1.81 x 25mm...
Powerglide Upper Kickdown Clip
OER® Authorized reproduction upper kickdown clip for models with powerglide automatic transmission. Connects the upper passing gear kickdown rod to the bellcrank assembly. Applications: 1967-69 Camaro with Powerglide...
1955-57 Chevrolet Bel Air, 150, 210, Nomad; Fuel tank Sending Unit Installation Set
Reproduction components necessary to Install the fuel tank sending unit for 1955-57 Chevrolet Bel Air, 150, and 210 passenger car models. This hardware set includes the sending unit gasket, O-ring, filler tank to neck O-ring,...
1955-81 Retainer Clip; Trans Control Rod, Clutch Push Rod, Throttle Rod Swivel
OER® reproduction clip for a variety of different parts on 1955-81 GM vehicles. This clip was used to attach the throttle valve control rod, throttle lever rod swivel, and the upper and lower clutch push rods. Use as...
1962-1982 GM; Carburetor, Door, Tailgate; Spring Steel Rod Clip; RH Passenger Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...
5/16-18 X 9/16" Self-Tapping Bolt. Brake and fuel line bolts with correct Anchor head marking. Self tapping, non pointed 1/2" bolt. Set of 6. {fitment}