Chrome Trim Screw, #8 x 3/4", With #8 Phillips Oval Head
Replacement chrome plated trim screws used on various GM vehicles. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality reproductions. This part is original...
Flat Washer; 1/2" USS; Zinc Plated
1/2" USS zinc plated Flat Washer for a variety of applications. A washer is a thin plate (typically disk-shaped) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such...
1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon
Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...
1958-96 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 13/16"; Black Phosphate; Each
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. Note: For a money saving set of 10 use...
1959-80 AMC, GM, Ford, Mopar; Trico Windshield Wiper Blade; 15" Length; Various Models; Each
Reproduction 15 inch "TRICO Style # PR-15-2W" wiper blade for a wide variety of classic vehicle models. Each blade features stainless steel construction and is loaded with a period-correct TRICO RF-15 style insert with a...
1955-59 Chevy, Ford; Windshield Wiper Blade; 12"; Triple-Action; Wrist-Action Connector; Stainless
Reproduction windshield wiper blade for 2nd design 1955 models and all 1956-59 Chevrolet and GMC truck models. Also correct as a replacement for a wide range of other makes and models, including 1955-57 GM passenger models...
Why leave your convertible top boot in the trunk exposed when you can keep it protected with this special top boot vinyl storage bag. Designed to keep your top boot safe and clean, this bag prevents dust, dirt, and damage...
U-Nut; M6 - 1.0; Panel Range.030" to.160"; Center of Hole to Edge: 17/32"; Black Phosphate; Each
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160") Specifications: OE #: 11503957 Quantity: Individual Clip...
1956 Ford Pickup; Back Window Glass; Big Window; Dark Gray Privacy Tint
Reproduction back glass for 1956 Ford pickup truck models. Replacing your broken or missing back glass with this quality reproduction will enhance the appearance and safety of your vehicle by helping you see clearly. Don't...
1956 Ford Pickup; Back Window Glass; Big Window; Clear
Reproduction back glass for 1956 Ford pickup truck models. Replacing your broken or missing back glass with this quality reproduction will enhance the appearance and safety of your vehicle by helping you see clearly. Don't...
1956 Ford F100, F250, F350 Pickup Truck; Front Windshield Glass; Tinted
Reproduction of the original front windshield glass for use with 1956 Ford F100, F250, F350 pickup truck models. This windshield is manufactured with tempered laminate safety glass that meets the standard for protection...
3/8"-16 x 15/16" Bumper Bolt With Flat; Zinc Plated Shank; Stainless Steel Flat Head; Each
Correct replacement style bolt to replace the original missing or damaged bumper bolt. Each bolt is manufactured to original specifications and will match the original. Fits a variety of different years and models. Measures...
Reproduction front windshield glass for 1956 Ford F100, F250, F350 pickup truck models. This windshield is manufactured with tempered laminate safety glass that meets the standard for protection against road debris. Each...
1953-56 Ford F100, F250, F350 Pickup; Front Inner Fender Apron; Passenger Side; EDP Coated
Reproduction of the original passenger-side front inner fender apron foruse with 1953-56 Ford F100, F250, F-350 pickup truck models. This OE-style inner fender is designed as a direct fit replacement for Ford F-Series trucks....
Replacement style stainless steel capped bumper bolt and nut designed for use on many GM vehicles. Each bolt measures 1/2"-13 x 1-1/2"; 1-1/8" head diameter and comes complete with attaching nut. Can be used for a wide...
1948-72 Ford F1, F2, F-100, F-250 FlareSide Pickup; Rear Bumper; Plain; Paintable
Reproduction paintable rear bumper for 1948-72 Ford F1, F2, F-100, F-250 FlareSide (stepside) and 1973-77 4x4 F-250 FlareSide (stepside) trucks. This bumper features heavy gauge cold rolled steel construction with the correct...
Ford, GM, Mopar; Windshield Wiper Blade Refill; 16"; Pair
Reproduction of the windshield wiper blade inserts for various models equipped with 16" wiper blades. Each blade insert is manufactured for perfect fit, function and appearance when used with the proper blade assembly....
1960-84 Windshield Wiper Blade; 16" Trico; Rainbow Type; 1/4" Bayonet Connector; Matt Stainless
Reproduction of the original Trico Rainbow Type wiper blade designed for various models originally equipped with Trico blades. Each wiper blade will replace the original and offer years of service. Each blade comes complete...
1953-56 Ford F100, F250, F350 Pickup; Front Bumper To Arm Bracket Set; Chrome
Reproduction front bumper to arm brackets for use with 1953-56 Ford F100, F250, and F350 pickup truck models. Each bracket is manufactured in stamped steel replicating the original design and fitment. Features a bright...
1965-2002 GM; Door Lock Striker Washer; 3.50MM Thick; Each
Correct reproduction of the original threaded striker washer for use on 1965-2002 Buick, Chevrolet, Pontiac, and Oldsmobile models as listed. The door lock striker washer is installed on the door jamb for either the right or...
1953-56 Ford F-100, F-250, F-350; Upper Or Lower Door Hinge; RH Or LH; 4 Required; Each
Reproduction of the original door hinge designed for use with 1953-56 F100, F250, F350 pickup truck models. Each door hinge is manufactured in heavy-duty stamped steel to correct factory specifications replicating the...
Tapping Screw; #8 x 1"; Phillips Pan Head; A/AB; Black Oxide
This reproduction screw can be used on many applications where a #8 X 1" phillips pan head Black Oxide plated tapping screw is needed. Sold individually.
1967-69 Camaro, Firebird; Convertible Top Boot Interior Snaps; with Screws; 4 Piece Set
Reproduction convertible top boot snap and screw set for 1967-69 Camaro and Firebird models and any other vehicle that requires a screw-on style snap. These snaps are used to secure the convertible top to the inner rear...
1956 Ford F-Series Pickup, F-100, F-250; Door Window Glass; Tempered; Smoke Gray Tint
Reproduction front door glass window for 1956 Ford F-Series pickup trucks. Each glass panel is molded in tempered glass with the correct shape and curvature for a precise fit and authentic appearance. Replacing your original...
Reproduction zinc-plated bumper bolt with a polished stainless steel capped head for a variety of GM, Ford and Mercury applications including 1958-66 Chevrolet, 1965-68 Ford Mustang, 1960-67 Ford Falcon and 1960-65 Mercury...
Reproduction 16" windshield wiper blade for a variety of GM vehicles that require a 16" side lock blade. Each blade is manufactured in stainless steel and finished in satin silver as original. Fits the side lock style...
1956 Ford F-Series Truck; Hood Hinge Assembly; LH - Driver Side
Reproduction driver side hood hinge assembly for 1956 F-Series pickups. This hinge fits Ford F-100, F-250, and F-350 trucks. Replaces Ford part# B6TZ-16797-A. {fitment}
Spring Steel Rod Clip, for Carburetor, Door, Tailgate; LH Driver Side
OER® Authorized reproduction of the original style carburetor rod to accelerator rod clip for various models. Each clip is manufactured in stamped steel and heat treated for strength and durability. For use on the various...
1953-56 Ford F100, F250, F350 Pickup; Front Bumper To Arm Bracket Set; Black EDP Coated
Reproduction of the original front bumper to arm brackets designed for use with 1953-56 Ford F-100, F-250, and F-350 pickup truck models. This set includes both driver and passenger side brackets and hardware. Replaces Ford...
Door Lock Striker Bolt Washer Shim ; 1.25MM Thick ; Each
Reproduction of the original door striker bolt shim manufactured in die-stamped steel and finished in clear zinc coating. Used to correctly position the door striker bolt for proper alignment with the door latch assembly. Use...
1956 Ford F-100, F-250, F-350 Truck; Door Latch Assembly; LH Driver Side
Reproduction driver side door latch assembly for 1956 Ford F-100, F-250, and F-350 pickup truck models. This direct replacement latch assembly is manufactured to correct factory specifications and will install, fit and...
1956 Ford F100, F250, F350 Truck; Door Latch Assembly; RH Passenger Side
Reproduction passenger side door latch assembly for 1956 Ford F-100, F-250, and F-350 pickup truck models. This direct replacement latch assembly is manufactured to correct factory specifications and will install, fit and...
Shims are very important items when installing and aligning sheet metal. Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure...
1967-81 GM; Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; for Hood Hinges; 8 Piece Set; Various Models
OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"-16 x 1" specs....
Hex Washer Head Spin Lock Bolt; 5/16" X 18 X 1-1/4"; Phospate Coating" Each
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished iin a black phospate coating for an authentic original appearance and corrosion resistance. Sold individually. Use as required. Product Specifications:...
1953-60 Ford F-Series Truck; Outer Door Handle; RH
Reproduction passenger side outside door handle for 1953-60 Ford F100, F250, and F350 Pickup Trucks. This high quality reproduction features OE-style die-cast construction, and a triple chrome-plated finish. Includes pads and...
Bumper Bolt; Stainless Steel Cap; Flat Head; 3/8"-16X 15/16"; Package of 25
Package of 25 reproduction bumper bolts that measure 7/16-14 x 1-1/2" with a stainless steel cap and round head. Willl fit a wide variety of vehicles including 1957-72 Ford F-Series Truck and many other Ford Motor Company...
Black phosphate-coated hex head bolts with a washer. Measures 3/8"-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck,...
Reproduction of the original Trico Style wiper blade refill designed for use on the various models that require a 16" Trico style rainbow type wiper blade. Each wiper blade assembly will replace the original and offer years...
1956 Ford F-Series Pickup, F-100, F-250; Vent Window Glass; Tempered; Smoke Gray Tint
Reproduction front door vent glass window for 1956 Ford F-Series pickup trucks. Each glass panel is molded in tempered glass with the correct shape and curvature for a precise fit and authentic appearance. Replacing your...
#10-24 x 1"; Phillips Oval Head Head Machine Screw; Stainless Steel
Stainless Steel Phillips #10-24 x 1" Oval Head Head Machine Screw. Sold individually. Specifications: Thread Diameter : 10-24 Length : 1" Head Style : Phillips Oval Head Size : Std Material : 18-8 Stainless Steel
Plastic Retainer; Push-In Type Rivet; 7/8" Head Diameter; 1-3/64" Stem Length; For 1/2" Hole
Reproduction push-in retainer designed to attach the front urethane bumper cover to the impact bar. Push-in style. 28.2mm long. Manufactured in durable ABS black plastic material. Sold individually. Use as required. Replaces...
Hex Washer Head Spin Lock Bolt; Phospate Coating; 5/16" X 18 X 1-1/4"; Set of 24
Reproduction 5/16" x 18 x 1-1/4" hex washer head spin lock bolt finished in a black phospate coating for an authentic original appearance and corrosion resistance. Set of 24. Use as required. Product Specifications: Thread...
U-Nut Set; M6 - 1.0; Panel Range.030" to.160"; Black Phosphate; 25 Piece Set
Black phosphate metric u-nut or foldover nut, that measures M6-1.0 to install and secure various components. Fits panel thickness from.80mm to 4 mm. (.030" to.160"). Set of 25 u-nuts. Specifications: OE #: 11503957 Quantity:...
1956 Ford F-Series Pickup, F-100, F-250; Vent Window Glass; Tempered; Clear
Reproduction front door vent glass window for 1956 Ford F-Series pickup trucks. Each glass panel is molded in tempered glass with the correct shape and curvature for a precise fit and authentic appearance. Replacing your...
Installation hardware set for various 1985-92 Camaro models including IROC-Z models. Each set includes 18 of reproduction # 11508023 bolt. Specifications: Quantity: Set of 18 Class: 9.8 Color: Black Phosphate Material: Steel...
Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...
Tapping Screw; Hex Washer Head; #8-18 x 1/2" Long; Black Oxide
Hex, washer head #8-18 x 1/2 tapping screw, in phosphate and oil coating for various applications including mounting grill to various classic vehicles Screw Specs: Description : Tapping Screw Screw Size : #8 Length : 1/2"...
Hex Bolt; 1/2"-13 x 4" LG; Gd 8; Yellow Dichromate
Hex Bolt; 1/2"-13 x 4" Lg; Gd 8; Yellow Dichromate Application 1973-1980 Chevrolet/GMC Radiator Core Support; STD Cab 1/2 & 3/4 Ton 1973-1980 Chevrolet/GMC Radiator Core Support; Crew Cab 3/4 Ton 1973-1980 Chevrolet/GMC Front...
1955-74 GM; Bolt, Pointed Tip with Hex Washer Head, 5/16-18 x 3/4"; Black Phosphate; 10 Piece Set
OER® Authorized reproduction of the original hex head bolt for various GM models. This bolt was used for the installation of a number of parts on the front end of various GM models. The OER® Authorized logo represents...
Bolt, 1/4-20 x 1-3/16" Dog Point Tip With Free Spinning Washer, Black Phosphate, 10 Piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
Bolt, 5/16-18 x 1" Pointed Tip With Hex Washer Head, Black Phosphate, 10 Piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
Bolt, 5/16-18 X 7/8" Pointed Tip With Free Spinning Washer, Black Phosphate, 10 piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
Bolt, 3/8-16 X 1" Pointed Tip With Free Spinning Washer, Black Phosphate, 10 Piece Set
Replacement bolt used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these quality...
U-Type Clip Nut, Fits #8 Screw, Black Phosphate Coated
Replacement U-clip nuts used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. Correct hardware can make any installation job easier. Replace your missing or damaged hardware with these...
Tapping Screw; #8 x 1"; Phillips Pan Head; A/AB; Zinc
This phillips head tapping screw is zinc plated steel to prevent corrosion and has a pan head. It's a size #8 x 1". Screw Size : #8 Length : 1" Head Style : Phillips pan Point Type : A/AB Finish : Zinc Applications: 1972-73...
1/2"-13 Prevailing Torque Lock Nut; Cadmium Plated
1/2"-13 Prevailing Torque Lock Nut; Grade 8; Cadmuim Plated
Bolt; 1/2"-13 x 5" Lg Hex Head Cap Screw; Grade 8
1/2"-13 x 5" Hex Head Cap Screw; Grade 8